tHINK I FOUND THE OIL PROBLEM TELL ME WHAT YOU THINK
#1
Junior Member
Thread Starter
Join Date: Oct 2004
Location: oklahoma city
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
tHINK I FOUND THE OIL PROBLEM TELL ME WHAT YOU THINK
i looked in the motor this morning when i finally had enough light to see what the heck i was doing and i noticed that all the oil coming out of the engine is coming from these two little bolts on the front of the engine , one of the bolts is showing the threads like for a 1/4 of an inch should i tighten this up, do you think that is the only problem and does this happen naturally over time, in other words should i check this every time i get the oil changed?
slowly learning,
Djadict_d
slowly learning,
Djadict_d
#4
I R SAD PANDA W/O BAW
First off... BE VERY CAREFUL! DO NOT TOUCH THOSE PLASTIC LINES! They are very very brittle and can snap if you breath on them. They are for your oil injection. You can tighten those loose bolts. They should be 10mm. Be careful not to snap them. How big of an oil leak were you having? There isnt much pressure at all in there. Anyways they should be loose and shouldnt come loose so just tighten them.
#5
Junior Member
Thread Starter
Join Date: Oct 2004
Location: oklahoma city
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
well it would leak to a little puddle of about 6 inches in diameter and i did what you told me to and i also cleaned it up a little everything seems to be working ok, what i found was that three of the banjo bolts were finger loose so i tightened them up a bit and then put everything back together so we will see if that fixed the problem...
one other question my shifter pole on my manual tranny gets really warm when driving a while is that common, i can take the center peice out and touch the plastic and i cant even hold my hand there that long, my friend said it might be that the tranny doesnt have enough grease in it if thats true what should i do ?
one other question my shifter pole on my manual tranny gets really warm when driving a while is that common, i can take the center peice out and touch the plastic and i cant even hold my hand there that long, my friend said it might be that the tranny doesnt have enough grease in it if thats true what should i do ?
#6
I R SAD PANDA W/O BAW
All the shifters of the FCs I have driven get pretty hot. Your rubber insulation bushings are probably gone. Tranny doesnt use grease, it only has tranny fluid. The shifter assembly on the otherhand may have a little grease in there. Look it up in the FSM.
#7
Junior Member
Thread Starter
Join Date: Oct 2004
Location: oklahoma city
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
ok i drove it a little and the smell from the oil is still there and it is still leaking i looked under the car a saw that the oil pan is where the leak is i havent checked the bolt on the pan i guess i should do that but do you think there could be any other problems "where the leak may be " ???
Trending Topics
#8
Senior Member
Join Date: Mar 2004
Location: Victoria, BC
Posts: 350
Likes: 0
Received 0 Likes
on
0 Posts
Make sure ytou have the 4 copper crush washers on the OMP lines amd the 4 holed copper washer behind the lines as well as it will leak without them.
Careful if you try to tighten the oil pan as well as it will crack and distort if you try and crank it down hard. You can snug the bolts up a bit if they are loose by going opposite side side bolt tightening, but be careful. Usually if the pan is leaking you need to reseal it (new gasket and/or RTV) though.
Careful if you try to tighten the oil pan as well as it will crack and distort if you try and crank it down hard. You can snug the bolts up a bit if they are loose by going opposite side side bolt tightening, but be careful. Usually if the pan is leaking you need to reseal it (new gasket and/or RTV) though.
#10
I live in an igloo
Join Date: Jul 2004
Location: calgary alberta
Posts: 2,546
Likes: 0
Received 0 Likes
on
0 Posts
Personally, I think that you should move the lines around, cause if they do ******* snap off becuase you were breathing on them, you ow it to your cars life to replace them anyways. If they don't, then its all good. My lines were fine, they were molded to the engine, but I could yank on them and nothing happened.
I think the only way the lines get like that is if your engine has overheated or something.
I think the only way the lines get like that is if your engine has overheated or something.
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM