Started Porting!!! Pics Included! Help!
#1
Rotors? What Are Those?
Thread Starter
iTrader: (6)
Join Date: Jul 2003
Location: Jefferson City, Tn
Posts: 2,601
Likes: 0
Received 0 Likes
on
0 Posts
Started Porting!!! Pics Included! Help!
i just started the porting on a TII upper intake just to see how it goes its seems to be coming out very very well but here are some pics of just one of the intakes i began to port just started today so took me a while to clean up take off **** and start but there is where im at so far........
here they are any info would greatly help remember this is a low grit paper so looks kinda rough i will go up to like 400 by the end or even higher...
any good info helps..
TwEaK
here they are any info would greatly help remember this is a low grit paper so looks kinda rough i will go up to like 400 by the end or even higher...
any good info helps..
TwEaK
Last edited by TwEaK; 02-04-04 at 10:48 PM.
Trending Topics
#11
Rotors? What Are Those?
Thread Starter
iTrader: (6)
Join Date: Jul 2003
Location: Jefferson City, Tn
Posts: 2,601
Likes: 0
Received 0 Likes
on
0 Posts
ok Ty TRAINWRECK! ok guys this is just one of the inner holes of the begging of my porting ill admit it is ruff but remember i started it out rough to grind down all the metal (like the welding on the sides) got rid of it all and feels very slick without any bumbs once ifinish all 4 im gonna go to a high grit number like 350 then 500 then 600 to make it a real fine finish give me your thoughts on this
Thanks
TwEaK
Thanks
TwEaK
#13
Rotors? What Are Those?
Thread Starter
iTrader: (6)
Join Date: Jul 2003
Location: Jefferson City, Tn
Posts: 2,601
Likes: 0
Received 0 Likes
on
0 Posts
no no thats the upper intake for a TII when im done polishing it on the outside and porting it on the inside ill prolly sell it for cheap if not ill throw it out neways once i get some more cash ill get a high grit to start getting the imperfectiosn out
TwEaK
TwEaK
#14
Full Member
Join Date: Nov 2003
Location: North York, Ontario
Posts: 233
Likes: 0
Received 0 Likes
on
0 Posts
looks good so far...i've just started my tb mod/port/polish...any hints you've got would be appreciated...i'll keep ya posted as well, just gotta get the gf to scan some pics of it...
#15
Rotors? What Are Those?
Thread Starter
iTrader: (6)
Join Date: Jul 2003
Location: Jefferson City, Tn
Posts: 2,601
Likes: 0
Received 0 Likes
on
0 Posts
well im following a how to port i rarely got time im only 16 gonna take a while for me but all i can say make shure you dont have an "deeper" spots make shure its all even and its all circles or at least by the time you do the last touch ups make shure its a circle finish how you see mine... and is yours a N/A or TII ??? the TII manifold (shown) is alot harder to reach to the top parts but really make shure eveything comes out in "circular" form
TwEaK
TwEaK
#17
Full Member
Join Date: Nov 2003
Location: North York, Ontario
Posts: 233
Likes: 0
Received 0 Likes
on
0 Posts
I've searched and found pretty much everything I need (groan, I *hope*) lol it's a 87 TII. Im also looking at a flexible extention for my dremel so I can snake down into the dynamic chamber to polish it up. Like you said, it's all about finding the time...
Thread
Thread Starter
Forum
Replies
Last Post