2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

No start after replacing fuel pump

Thread Tools
 
Search this Thread
 
Old Apr 22, 2017 | 04:45 PM
  #1  
Dulaney71's Avatar
Thread Starter
Junior Member
 
Joined: Jun 2016
Posts: 7
Likes: 0
No start after replacing fuel pump

Bought 90 rx7 vert. drove it bout 30 miles home anything over 1/4 throttle start missing and backfiring. Replaced fuel injectors, plugs and wires, fuel filter it run little better but same problem! Replaced afm and fuel pump now won't start unless I spray a shot of starting fluid in air intake! Oh and tps checked out good! At my wits end trying to figure this car out! Any ideas?
Reply
Old Apr 22, 2017 | 11:45 PM
  #2  
misterstyx69's Avatar
Retired Moderator, RIP
Tenured Member: 20 Years
iTrader: (142)
 
Joined: Sep 2005
Posts: 25,581
Likes: 136
From: Smiths Falls.(near Ottawa!.Mapquest IT!)
did you get any engine codes on this car?
Reply
Old Apr 23, 2017 | 05:57 PM
  #3  
Dulaney71's Avatar
Thread Starter
Junior Member
 
Joined: Jun 2016
Posts: 7
Likes: 0
Won't show any codes!
Reply
Old Apr 25, 2017 | 06:20 PM
  #4  
Dulaney71's Avatar
Thread Starter
Junior Member
 
Joined: Jun 2016
Posts: 7
Likes: 0
shows code 27 and 37
Reply
Old Apr 28, 2017 | 12:19 AM
  #5  
misterstyx69's Avatar
Retired Moderator, RIP
Tenured Member: 20 Years
iTrader: (142)
 
Joined: Sep 2005
Posts: 25,581
Likes: 136
From: Smiths Falls.(near Ottawa!.Mapquest IT!)
Your Electric OMP has bit the dust..and it has(or Could have ) a tendency to damage the ECU if you try to run the car continuously with the car in Limp mode.
Limp mode is the Code 27 that you are getting and makes the car act like **** above 3500 Rpm
Reply
Old May 1, 2017 | 09:07 PM
  #6  
Dulaney71's Avatar
Thread Starter
Junior Member
 
Joined: Jun 2016
Posts: 7
Likes: 0
Well put another omp on it and another ecu! Still going into limp mode! Any ideas?
Reply
Old May 2, 2017 | 06:10 AM
  #7  
roTAR needz fundZ
Tenured Member 15 Years
iTrader: (1)
 
Joined: Aug 2002
Posts: 2,614
Likes: 31
From: Freeland, MI
You probably got a crap omp and ecu
Reply
Old May 5, 2017 | 10:32 PM
  #8  
Dulaney71's Avatar
Thread Starter
Junior Member
 
Joined: Jun 2016
Posts: 7
Likes: 0
Well it ran great for about an hour yesterday! Pulling back in at house and it goes back into limp mode! Turn off ignition and let set bout 5 minutes and crank it up again runs perfect for bout 30 minutes then same thing limp mode! Now it shows code 17
Reply
Old May 6, 2017 | 09:45 AM
  #9  
misterstyx69's Avatar
Retired Moderator, RIP
Tenured Member: 20 Years
iTrader: (142)
 
Joined: Sep 2005
Posts: 25,581
Likes: 136
From: Smiths Falls.(near Ottawa!.Mapquest IT!)
RX7 FD and Series 5 Error Codes
Reply




All times are GMT -5. The time now is 05:10 AM.