2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:

new rebuild Q's

Thread Tools
 
Search this Thread
 
Old 10-23-05, 08:15 PM
  #1  
Full Member

Thread Starter
 
zerrorx7's Avatar
 
Join Date: Feb 2005
Location: alberta, canada
Posts: 166
Likes: 0
Received 0 Likes on 0 Posts
new rebuild Q's

welll my s5 engine has over 2000miles on it and since iv had it been shaking...and i alway thought it was my timing.....so i got someone with lots of experince to do it and he said it was a biy off,,,however its still shaking...so i did a comp test and its good(willn have numbers later) he told me tht it be the housing which may had some lines...he said it may not be....so i just thought i would ask anybody here what i could try to slove my prob....its an stock 89 na

thanks
Old 10-23-05, 09:54 PM
  #2  
Full Member

Thread Starter
 
zerrorx7's Avatar
 
Join Date: Feb 2005
Location: alberta, canada
Posts: 166
Likes: 0
Received 0 Likes on 0 Posts
okay heres the numbers from a mazda tester
rotor#1
http://img464.imageshack.us/full.php...ture0531vj.jpg
rotor#2
http://img464.imageshack.us/full.php...ture0566ng.jpg
Old 10-23-05, 10:45 PM
  #3  
Lives on the Forum

iTrader: (8)
 
RotaryResurrection's Avatar
 
Join Date: Oct 2003
Location: Morristown, TN (east of Knoxville)
Posts: 11,576
Received 26 Likes on 19 Posts
welll my s5 engine has over 2000miles on it and since iv had it been shaking...and i alway thought it was my timing.....so i got someone with lots of experince to do it and he said it was a biy off,,,however its still shaking...so i did a comp test and its good(willn have numbers later) he told me tht it be the housing which may had some lines...he said it may not be....so i just thought i would ask anybody here what i could try to slove my prob....its an stock 89 na
What in the hell did you just say?

Old 10-23-05, 10:46 PM
  #4  
Full Member

 
FC or S13's Avatar
 
Join Date: Oct 2005
Location: Austin, TX
Posts: 86
Likes: 0
Received 0 Likes on 0 Posts
Good compression on the chambers should be 85 all around
Old 10-23-05, 10:46 PM
  #5  
Lives on the Forum

iTrader: (8)
 
RotaryResurrection's Avatar
 
Join Date: Oct 2003
Location: Morristown, TN (east of Knoxville)
Posts: 11,576
Received 26 Likes on 19 Posts
If the test was done correctly, those numbers are quite low. Mazda minimum spec for a decent engine is 85psi, as you can see you are below that by quite a bit, it appears 75psi and lower all around.
Old 10-23-05, 10:48 PM
  #6  
Likes to swear....alot

iTrader: (3)
 
R.P.M.'s Avatar
 
Join Date: Dec 2002
Location: Kitchener Ontario Canada
Posts: 3,791
Likes: 0
Received 3 Likes on 3 Posts
Shaking like how.....like when it's idling or when it driving down the road in the rpm's?

Who built the motor? Did they use the properly weight matched rotors? Are your motor mounts any good?
Old 10-23-05, 11:38 PM
  #7  
Full Member

Thread Starter
 
zerrorx7's Avatar
 
Join Date: Feb 2005
Location: alberta, canada
Posts: 166
Likes: 0
Received 0 Likes on 0 Posts
rx

yes it shakes when its idling only...and it runs reallly goood other then tht....and the engine mounts have seen better days...
well being at 75 psi what im i lookin at as for time....how long do u think she will go for...
sorry if its hard to read....no english

Last edited by zerrorx7; 10-23-05 at 11:42 PM.
Old 10-24-05, 11:54 AM
  #8  
Lives on the Forum

iTrader: (8)
 
RotaryResurrection's Avatar
 
Join Date: Oct 2003
Location: Morristown, TN (east of Knoxville)
Posts: 11,576
Received 26 Likes on 19 Posts
I'd say you've got 1-6 months.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Vartok
2nd Generation Specific (1986-1992)
16
10-08-15 04:49 PM
musker
New Member RX-7 Technical
1
10-01-15 05:58 PM



Quick Reply: new rebuild Q's



All times are GMT -5. The time now is 03:45 PM.