2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:

need part number for n20

Thread Tools
 
Search this Thread
 
Old 06-12-04, 11:05 PM
  #1  
a.k.a. Mike

Thread Starter
 
cmjaure's Avatar
 
Join Date: May 2004
Location: new mexico
Posts: 250
Likes: 0
Received 0 Likes on 0 Posts
need part number for n20

I am going to put nitrus on one of my rx7s and I need to know if it would be better for a wet or a dry system and if anyone has a part # for either. I would like a response from people who have it on thers. The 7 that is going to get it is a s4 gxl. thanks
Old 06-12-04, 11:08 PM
  #2  
Senior Member

 
88ROTARY's Avatar
 
Join Date: Jun 2003
Location: MONROE LA
Posts: 363
Likes: 0
Received 0 Likes on 0 Posts
what brand of n20
Old 06-12-04, 11:11 PM
  #3  
a.k.a. Mike

Thread Starter
 
cmjaure's Avatar
 
Join Date: May 2004
Location: new mexico
Posts: 250
Likes: 0
Received 0 Likes on 0 Posts
well anything that somebidy has had good luck with
Old 06-12-04, 11:13 PM
  #4  
Super Raterhater

iTrader: (6)
 
SonicRaT's Avatar
 
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,624
Likes: 0
Received 2 Likes on 2 Posts
Check out the how-to on fc3s.org, they talk about both the wet and dry setup's (with part numbers!)
Old 06-12-04, 11:14 PM
  #5  
a.k.a. Mike

Thread Starter
 
cmjaure's Avatar
 
Join Date: May 2004
Location: new mexico
Posts: 250
Likes: 0
Received 0 Likes on 0 Posts
thank you
Old 06-12-04, 11:16 PM
  #6  
Super Raterhater

iTrader: (6)
 
SonicRaT's Avatar
 
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,624
Likes: 0
Received 2 Likes on 2 Posts
Here's a direct link for those of you too lazy to browe the fc3s site.

http://www.fc3s.org/how_tos/engine/nos_wet.html
Old 06-12-04, 11:25 PM
  #7  
Open up! Search Warrant!

 
Project84's Avatar
 
Join Date: May 2002
Location: Kicking down doors in a neighborhood near you
Posts: 3,838
Likes: 0
Received 2 Likes on 2 Posts
this is extremely informative, I suggest you read it.

Also, you have brought up a sensitive, very misunderstood topic (nitrous oxide) so tread lightly, and as you read what others post, remember to discern fact from opinion.

https://www.rx7club.com/showthread.p...hreadid=111605

I have a NOS brand system installed but I have yet to use it. I'm finishing swapping out my auto transmission for a manual and then I want to make sure my stand alone engine management system is tune right before I hit the juice.

Last edited by Project84; 06-12-04 at 11:31 PM.
Old 06-13-04, 01:23 AM
  #8  
Senior Member

 
Bebesito21's Avatar
 
Join Date: Jan 2003
Location: Tampa, Fl
Posts: 387
Likes: 0
Received 0 Likes on 0 Posts
75-80 shot wet set up will work without a problem. Im at a 200 shot right now. Just make sure you did all of the reliability mods and dont spray on an empty bottle. It will blow your engine.....(ask me how i know)
Old 06-13-04, 01:33 AM
  #9  
Open up! Search Warrant!

 
Project84's Avatar
 
Join Date: May 2002
Location: Kicking down doors in a neighborhood near you
Posts: 3,838
Likes: 0
Received 2 Likes on 2 Posts
If you run out of nitrous, then you should just run way rich on fuel. How would that blow the engine?
Old 06-13-04, 01:40 AM
  #10  
Senior Member

 
Bebesito21's Avatar
 
Join Date: Jan 2003
Location: Tampa, Fl
Posts: 387
Likes: 0
Received 0 Likes on 0 Posts
The bottle pretty much was down to vapor so it was spraying on/off. It felt like the car was stuttering. Dont know if you understand what i mean. But i ended up blowing an apex seal.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
diabolical1
2nd Generation Specific (1986-1992)
30
01-30-16 05:50 AM
josef 91 vert
2nd Generation Specific (1986-1992)
23
09-03-15 11:20 AM



Quick Reply: need part number for n20



All times are GMT -5. The time now is 03:48 PM.