n/a to turbo 2 swap
#1
Junior Member
Thread Starter
Join Date: Oct 2009
Location: puyallup
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
n/a to turbo 2 swap
I've been looking for an hour and can't find a thread for the swap.
I have these questions basically.
What all is needed to do a swap.
I have 87 n/a rx7 want to put a turbo 2 motor into it.
Can i use a engine/tranny/ecu/harness from a s5 rx7 or s4 would be alot easier?
What all components will I need for successful swap ei: engine/tranny/driveshaft/etc?
thanks
I have these questions basically.
What all is needed to do a swap.
I have 87 n/a rx7 want to put a turbo 2 motor into it.
Can i use a engine/tranny/ecu/harness from a s5 rx7 or s4 would be alot easier?
What all components will I need for successful swap ei: engine/tranny/driveshaft/etc?
thanks
#3
Space cadet
iTrader: (78)
I've been looking for an hour and can't find a thread for the swap.
I have these questions basically.
What all is needed to do a swap.
I have 87 n/a rx7 want to put a turbo 2 motor into it.
Can i use a engine/tranny/ecu/harness from a s5 rx7 or s4 would be alot easier?
What all components will I need for successful swap ei: engine/tranny/driveshaft/etc?
thanks
I have these questions basically.
What all is needed to do a swap.
I have 87 n/a rx7 want to put a turbo 2 motor into it.
Can i use a engine/tranny/ecu/harness from a s5 rx7 or s4 would be alot easier?
What all components will I need for successful swap ei: engine/tranny/driveshaft/etc?
thanks
if you want the swap to go easy..
basically just get a S4 T2 engine(87-88= s4)( so every thing wires up)
your going to need the boost sensor, t2 fuel pump or a walbro 255 pump, ecu and harness(s4 t2)
get the t2 drive train... trans, driveshaft, lsd and half shafts.
your going to need a t2 hood unless you are going with fmic or something..
Last edited by Battle Cat; 10-20-09 at 02:13 AM.
#6
Junior Member
Thread Starter
Join Date: Oct 2009
Location: puyallup
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
I can't read your sig I need ten post lol. I found a thread earlier stating you don't have to be in series or swap drive trains. He just took the counter weights and flywheel off the n/a motor and put it on the turbo motor so he didn't have to swap tranny or difs is that right?
#7
Listen to King Diamond.
iTrader: (4)
I can't read your sig I need ten post lol. I found a thread earlier stating you don't have to be in series or swap drive trains. He just took the counter weights and flywheel off the n/a motor and put it on the turbo motor so he didn't have to swap tranny or difs is that right?
Trending Topics
#8
Rotorhead
Join Date: Feb 2001
Location: Charlottesville, Virginia, USA
Posts: 9,136
Likes: 0
Received 39 Likes
on
33 Posts
In that case, you don't have the required intelligence level to perform a swap yourself. About 3% of the population is retarded, so don't take this as an insult, as it's not your fault. I suggest that you have a professional shop perform the work.
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM