2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:

n/a FC wont start

Thread Tools
 
Search this Thread
 
Old 02-18-09, 08:08 PM
  #1  
No Pistons
Thread Starter
 
DRFTFC23's Avatar
 
Join Date: Nov 2008
Location: Calgary
Posts: 64
Likes: 0
Received 0 Likes on 0 Posts
n/a FC wont start

So my fc wont start its an n/a
the last time i drove the ar it was basically out of gas so i put it in the garage and left it for a few days then i went and bought gas and put it in so im not sure if the car ran out of gas or not but now it wont start?? ive tried cranking it like 5 or 6 times and it turns over but wont start so i dont know wuts the problem??
could it be flooded now?? how do i check if its flooded?? or wut toher things could cause this??
any help would be great asap
thanks guys
Old 02-18-09, 08:14 PM
  #2  
Smoke moar

 
cmanns's Avatar
 
Join Date: Aug 2006
Location: The yay, California
Posts: 2,530
Likes: 0
Received 1 Like on 1 Post
Pull spark plugs

Pull EGI fuse

Crank over

Clean off plugs with wire brush if they look bad, add alittle ATF fluid or Oil in each top plug hole, replace fuse and plugs and she should fire up.

If doesn't start then could be your fuel filter or fuel pump sock got dirty when it ran out of gas I think.

Sounds like my car when it was badly flooded and had bad plugs, if they don't look good replace them asap, mine would "flood" every time I tried to fire her up.
Old 02-18-09, 09:30 PM
  #3  
No Pistons
Thread Starter
 
DRFTFC23's Avatar
 
Join Date: Nov 2008
Location: Calgary
Posts: 64
Likes: 0
Received 0 Likes on 0 Posts
k ill go try that rite now and let you know if it helps
Old 02-18-09, 09:39 PM
  #4  
No Pistons
Thread Starter
 
DRFTFC23's Avatar
 
Join Date: Nov 2008
Location: Calgary
Posts: 64
Likes: 0
Received 0 Likes on 0 Posts
also wut egi fuse do i pull??
and how much oil do i pour in each spark plug hole??
and wut kind of oil??
Old 02-18-09, 10:23 PM
  #5  
Senior Member

iTrader: (7)
 
MMoore4545's Avatar
 
Join Date: Dec 2008
Location: WNC
Posts: 603
Likes: 0
Received 0 Likes on 0 Posts
Egi fuse is on/next to the drivers shock tower in the engine bay

a teaspoon is plenty

and whatever oil you run in your engine. if you have it laying around, I use two stroke
Old 02-18-09, 10:26 PM
  #6  
Full Member

 
Hunter4Life's Avatar
 
Join Date: Jun 2008
Location: Canada
Posts: 140
Received 0 Likes on 0 Posts
Originally Posted by DRFTFC23
also wut egi fuse do i pull??
and how much oil do i pour in each spark plug hole??
and wut kind of oil??
There is only one and its in the main fuse box in the engine bay. Pull it out crank it a couple times (this disables the fuel pump) and put it back in and crank it over a couple times. If it's flooded pull out plugs and get rid of excess fuel, then clean the plugs or put in new ones. As for the oil once you have got the plugs done put in about a teaspoon of 20w30 or Atf in the LOWER spark plugs holes then try starting it (with plugs in of course)
Old 02-18-09, 10:45 PM
  #7  
No Pistons
Thread Starter
 
DRFTFC23's Avatar
 
Join Date: Nov 2008
Location: Calgary
Posts: 64
Likes: 0
Received 0 Likes on 0 Posts
Thanks for everything guys i got it started but the only thing i didnt do was put oil in the spark plug holes, but it fired up and runs good now
so i was just wondering what is the purpose of the oil??
Old 02-18-09, 11:03 PM
  #8  
Smoke moar

 
cmanns's Avatar
 
Join Date: Aug 2006
Location: The yay, California
Posts: 2,530
Likes: 0
Received 1 Like on 1 Post
It helps build temporary compression, mostly needed with older engines at times.
Old 02-18-09, 11:52 PM
  #9  
No Pistons
Thread Starter
 
DRFTFC23's Avatar
 
Join Date: Nov 2008
Location: Calgary
Posts: 64
Likes: 0
Received 0 Likes on 0 Posts
ok but since it started and runs now it should be fine that i didnt use it right??
Old 02-19-09, 03:22 AM
  #10  
Full Member
 
hypestar1983's Avatar
 
Join Date: Feb 2009
Location: Greensboro NC
Posts: 149
Likes: 0
Received 0 Likes on 0 Posts
yep your fine now that its started, anytime you can smell gas coming out the exhaust you've flooded the car
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
sherff
Adaptronic Engine Mgmt - AUS
5
09-12-15 12:22 PM
TwentyDW
2nd Generation Specific (1986-1992)
4
09-02-15 06:42 PM
rx7shirley
2nd Generation Specific (1986-1992)
6
09-02-15 02:11 PM



Quick Reply: n/a FC wont start



All times are GMT -5. The time now is 05:34 AM.