motor pic
04-25-05, 11:12 PM
#1
oodle the noodle
Thread Starter
Join Date: Feb 2002
Location: brick, nj
Posts: 340
Likes: 0
Received 0 Likes
on
0 Posts
motor pic
finally it runs again......
1/2 bridge, no emissions, ported i/m&t/b, msd 6a, sx fpr, stainless lines, koyo rad, mindtrain header, more stuff i cant remember right now......custom airbox, cooling panel....how am i doin???
1/2 bridge, no emissions, ported i/m&t/b, msd 6a, sx fpr, stainless lines, koyo rad, mindtrain header, more stuff i cant remember right now......custom airbox, cooling panel....how am i doin???
04-25-05, 11:14 PM
#2
BOOSTED Vert
Join Date: Sep 2002
Location: Miami
Posts: 2,307
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by superpimp35
finally it runs again......
1/2 bridge, no emissions, ported i/m&t/b, msd 6a, sx fpr, stainless lines, koyo rad, mindtrain header, more stuff i cant remember right now......custom airbox, cooling panel....how am i doin???
1/2 bridge, no emissions, ported i/m&t/b, msd 6a, sx fpr, stainless lines, koyo rad, mindtrain header, more stuff i cant remember right now......custom airbox, cooling panel....how am i doin???
04-25-05, 11:42 PM
#4
Senior Member
Join Date: Jun 2002
Location: Calgary, A.B.
Posts: 407
Likes: 0
Received 0 Likes
on
0 Posts
where is the 1/2 bridge? on the center housing or the end housings? or did you use turbo 4 port housings?
Im just really interested b/c i was planning on doing a half brigde on mine when my car dies.
nice clean car you got there, more pictures
Im just really interested b/c i was planning on doing a half brigde on mine when my car dies.
nice clean car you got there, more pictures
04-25-05, 11:57 PM
#5
oodle the noodle
Thread Starter
Join Date: Feb 2002
Location: brick, nj
Posts: 340
Likes: 0
Received 0 Likes
on
0 Posts
nope, i used the na 6 port housings, the primary port is an agressive street port, and the aux port is cleaned up with a "little" lol bridge cut over it...
no vids as of yet.....just got it runnin and workin a few bugs out of it (little fuel sweats, oil level sender leaking ect.) gotta break it in, then get a microtech..
thanks for the comments....endless hours cleanin and polishin
no vids as of yet.....just got it runnin and workin a few bugs out of it (little fuel sweats, oil level sender leaking ect.) gotta break it in, then get a microtech..
thanks for the comments....endless hours cleanin and polishin
Trending Topics
04-26-05, 09:35 AM
#9
oodle the noodle
Thread Starter
Join Date: Feb 2002
Location: brick, nj
Posts: 340
Likes: 0
Received 0 Likes
on
0 Posts
right now the car has straight through exhaust....header,2.5 cat pipe, corksport catback....it is way too loud, so i have *sigh* a flowmaster to put on because its about one of the only things it wont burn out, and still sound decent....
my bridge doesnt activate by 5th 6th ports cause i ripped those out as well, along with the rats nest so the whole car has 2 vac lines ..and i also dont have any porting templates because it was done at jr's in long island....i saw the irons before he put them back in, and it was seriously one of the nastiest ports ive ever seen on a street car.(nasty being good)
my bridge doesnt activate by 5th 6th ports cause i ripped those out as well, along with the rats nest so the whole car has 2 vac lines ..and i also dont have any porting templates because it was done at jr's in long island....i saw the irons before he put them back in, and it was seriously one of the nastiest ports ive ever seen on a street car.(nasty being good)
04-27-05, 12:29 AM
#13
oodle the noodle
Thread Starter
Join Date: Feb 2002
Location: brick, nj
Posts: 340
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by porsche4786
Why the yellow top optima battery?
Thread
Thread Starter
Forum
Replies
Last Post
Azevedo
Other Engine Conversions - non V-8
26
03-01-19 09:19 PM