How to disconnect the wiring harness under the dash?
#1
Full Member
Thread Starter
Join Date: Jun 2005
Location: SoCal
Posts: 76
Likes: 0
Received 0 Likes
on
0 Posts
How to disconnect the wiring harness under the dash?
I had my engine rebuilt recently and have been cleaning it up and putting everything back on it. It looks like it would be so much easier to fully assemble the engine WITH the wiring harness and drop the engine in complete (except A/C and P/S), but I can't see how to get the the harness out form under the dash. I mean that literally; I can find any pictures and I sure can't get my head far enough under the dash or enough light, or my bifocals focused well enough...... The ECU and ???? (other one) under the floor mat are easy, but the seems to be two other wire bundles coming though the firewall that I can feel but can't see with eyes or fingers to find the connectors. Please tell me what you know. That's helpful.
#4
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
2nd gen.
you got a couple connectors on the passenger side firewall.
You have to remove the rocker plastic,pull the door seal back a bit then remove the passenger kick panel,and it will reveal some connectors.
Push the Engine harness INTO the passenger side by compressing the Big *** Rubber grommet into the firewall hole.
That will give you enough wire to work with to find out where the Connectors are.
There is one DOUBLE connector held onto the Kick panel by a 10 mm nut,and it is a Pain to get to,so leave it OFF when yo install it again.It will just be a ***** to get back on anyways..lol!
..I hope that is what you were referring to was the ECU wiring.!
you got a couple connectors on the passenger side firewall.
You have to remove the rocker plastic,pull the door seal back a bit then remove the passenger kick panel,and it will reveal some connectors.
Push the Engine harness INTO the passenger side by compressing the Big *** Rubber grommet into the firewall hole.
That will give you enough wire to work with to find out where the Connectors are.
There is one DOUBLE connector held onto the Kick panel by a 10 mm nut,and it is a Pain to get to,so leave it OFF when yo install it again.It will just be a ***** to get back on anyways..lol!
..I hope that is what you were referring to was the ECU wiring.!
#5
Full Member
Thread Starter
Join Date: Jun 2005
Location: SoCal
Posts: 76
Likes: 0
Received 0 Likes
on
0 Posts
Thanks guys, that was helpful. I will give it a try.
No gymnasts around this household, Chinese or otherwise. We're all 6'4"+ and 200-250 lb. Its tough getting under there!
To answer your next question, its a convertible that doesn't see the top unless it raining.
No gymnasts around this household, Chinese or otherwise. We're all 6'4"+ and 200-250 lb. Its tough getting under there!
To answer your next question, its a convertible that doesn't see the top unless it raining.
#6
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
I answered the same question for another gentleman who was about your size too,awhile back,so if you look up that thread with search it may have a little additional info.
#7
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,826
Received 2,594 Likes
on
1,842 Posts
Trending Topics
#8
That Would Be Me
Check my profile and go to my thread "pulling wire harness", mistertyx69 nailed it and I was able to disconnect and pull my harness with ease.