HELP with OS Giken T2SB and Throwout Bearing
#1
Full Member
Thread Starter
Join Date: Jan 2011
Location: Philippines
Posts: 100
Likes: 0
Received 0 Likes
on
0 Posts
HELP with OS Giken T2SB and Throwout Bearing
Hey guys
Recently come across this clutch:
I have an FD but with an FC transmission.
My question is can I use the stock throw out bearing (bearing and sleeve) with this clutch or do I have to purchase an OS Giken throwout bearing.
OS Giken support are saying I need theirs but I seeing hearing some guys on here are using their stock throwout bearing.
Just want to confirm this once again. Cheers...
Recently come across this clutch:
I have an FD but with an FC transmission.
My question is can I use the stock throw out bearing (bearing and sleeve) with this clutch or do I have to purchase an OS Giken throwout bearing.
OS Giken support are saying I need theirs but I seeing hearing some guys on here are using their stock throwout bearing.
Just want to confirm this once again. Cheers...
#2
87 SE WITH S5 T2 SWAP
iTrader: (11)
Hey guys
Recently come across this clutch:
I have an FD but with an FC transmission.
My question is can I use the stock throw out bearing (bearing and sleeve) with this clutch or do I have to purchase an OS Giken throwout bearing.
OS Giken support are saying I need theirs but I seeing hearing some guys on here are using their stock throwout bearing.
Just want to confirm this once again. Cheers...
Recently come across this clutch:
I have an FD but with an FC transmission.
My question is can I use the stock throw out bearing (bearing and sleeve) with this clutch or do I have to purchase an OS Giken throwout bearing.
OS Giken support are saying I need theirs but I seeing hearing some guys on here are using their stock throwout bearing.
Just want to confirm this once again. Cheers...
#5
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
That will not work.
the FC trans uses a PUSH type clutch and the FD uses a PULL type clutch.
2 different setups and 2 different Throw out bearings.
You need a Push type clutch and throw out bearing with the FC trans.(Yes even if it is on an FD engine)
Throw out bearings are rather cheap.(I got one at Mazda for about 70 CDN..but I did get one before,Federal Mogul bearing for $45 CDN).
the FC trans uses a PUSH type clutch and the FD uses a PULL type clutch.
2 different setups and 2 different Throw out bearings.
You need a Push type clutch and throw out bearing with the FC trans.(Yes even if it is on an FD engine)
Throw out bearings are rather cheap.(I got one at Mazda for about 70 CDN..but I did get one before,Federal Mogul bearing for $45 CDN).
#6
Post count is over rated
that pik is a push to pull conversion for an fd transmission. it is a push set up but will not work unless there is an fd bell housing on your t2 transmission. can you post pics of your transmission i can better help you then
#7
87 SE WITH S5 T2 SWAP
iTrader: (11)
Yes that is a conversion kit and it wont work without the fc bellhousing.Get the bearing kit from OS Giken,You can also get the adjustable clutch fork piece from OS.Is a upgraded fork setup that let you adjust it and is way thicker than the oem piece and it wont brake or bend if you have decent hp.I have run a triple and dual OS setups on my fc for ten years and they have never fail me.
Trending Topics
#8
Full Member
Thread Starter
Join Date: Jan 2011
Location: Philippines
Posts: 100
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for all your replies. Greatly appreciate the help.
The car is actually in the Philippines. So I don't have any pictures at the moment. All I do know is that I'm running an FC trans with a ORC 409 single plate clutch.
Given that this clutch is push type clutch. Can I simply install it and use the stock throwout bearing that's already in my FC trans ?
Sorry if I sound a bit like newb.
Anyways here are pictures of the clutch:
The car is actually in the Philippines. So I don't have any pictures at the moment. All I do know is that I'm running an FC trans with a ORC 409 single plate clutch.
Given that this clutch is push type clutch. Can I simply install it and use the stock throwout bearing that's already in my FC trans ?
Sorry if I sound a bit like newb.
Anyways here are pictures of the clutch:
#9
87 SE WITH S5 T2 SWAP
iTrader: (11)
yes
Thanks for all your replies. Greatly appreciate the help.
The car is actually in the Philippines. So I don't have any pictures at the moment. All I do know is that I'm running an FC trans with a ORC 409 single plate clutch.
Given that this clutch is push type clutch. Can I simply install it and use the stock throwout bearing that's already in my FC trans ?
Sorry if I sound a bit like newb.
Anyways here are pictures of the clutch:
The car is actually in the Philippines. So I don't have any pictures at the moment. All I do know is that I'm running an FC trans with a ORC 409 single plate clutch.
Given that this clutch is push type clutch. Can I simply install it and use the stock throwout bearing that's already in my FC trans ?
Sorry if I sound a bit like newb.
Anyways here are pictures of the clutch:
Thread
Thread Starter
Forum
Replies
Last Post
ls1swap
3rd Generation Specific (1993-2002)
12
10-01-15 07:58 PM