Engine rebuild
#1
Junior Member
Thread Starter
Join Date: Mar 2008
Location: Albuquerque, NM
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Engine rebuild
Ok so I just purchased a 1990 FC 13b turbo engine, and it has about 150k miles on it. I was wondering what should I replace when rebuilding it? I have looked at a bunch of different things and it seems that it will cost around $6k at the most to rebuild it completely.
What I found in order to rebuild an engine was:
1 complete kit including all brand new gaskets, oil o rings, seals, springs, bearings and what not - $1300
2 Brand new rotors - $650 each
2 New rotor housings (front and rear) - $700 each
1 Front (side) housing - $400
1 Intermidiate housing - $450
1 Rear (side) housing - $400
Total - $5250 only for engine
This engine will be used in drift competitions. So pretty much my question is. Out of all the listed parts which do you think will be neccessary to be replaced in order to have the engine running strong for next few years?
What I found in order to rebuild an engine was:
1 complete kit including all brand new gaskets, oil o rings, seals, springs, bearings and what not - $1300
2 Brand new rotors - $650 each
2 New rotor housings (front and rear) - $700 each
1 Front (side) housing - $400
1 Intermidiate housing - $450
1 Rear (side) housing - $400
Total - $5250 only for engine
This engine will be used in drift competitions. So pretty much my question is. Out of all the listed parts which do you think will be neccessary to be replaced in order to have the engine running strong for next few years?
#2
The Silent but Deadly Mod
iTrader: (2)
You may not need to buy rotors or housings, it depends on the condition of the engine.
If you've never rebuilt the engine before, I would suggest looking online for a rotary engine rebuild writeup. It may be hosted on www.rotaryresurrection.com.
If you've never rebuilt the engine before, I would suggest looking online for a rotary engine rebuild writeup. It may be hosted on www.rotaryresurrection.com.
#3
Full Member
Join Date: Dec 2001
Location: FK EPIC FU
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
Unless this is a learning experience for you, for 5 grand. just buy a complete rebuilt engine and skip the do-it yourself rebuild.
you also have other option of a professionally rebuilt block, like porting to name a few.
I've rebuilt 2 N/A rotary engines and turned just about every bolt that there ever was on an 2nd rx. The first rebuild was a complete fail. It may be better to get a rebuilt block. Else, looks like you want to get your own hands dirty.
you also have other option of a professionally rebuilt block, like porting to name a few.
I've rebuilt 2 N/A rotary engines and turned just about every bolt that there ever was on an 2nd rx. The first rebuild was a complete fail. It may be better to get a rebuilt block. Else, looks like you want to get your own hands dirty.
#4
Back at it again!!
iTrader: (3)
Join Date: Jun 2003
Location: Western Colorado
Posts: 1,324
Likes: 0
Received 0 Likes
on
0 Posts
Wow.
Unless an apex seal got mutilated, all you will need is a rebuild kit. I've always assembled my own (and many others) from 2 - 3 different sources and it usually costs me anywhere between $400 - $800 in parts.
I suggest that you get your block rebuilt at Rotary Resurrection.
Unless an apex seal got mutilated, all you will need is a rebuild kit. I've always assembled my own (and many others) from 2 - 3 different sources and it usually costs me anywhere between $400 - $800 in parts.
I suggest that you get your block rebuilt at Rotary Resurrection.
#5
Junior Member
Thread Starter
Join Date: Mar 2008
Location: Albuquerque, NM
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Yea, I see what you mean. I found a shop that builds rotary engines for $3400. One thing is though, I do not have an ECU or Wiring harness for the engine. Basically what I have is an empty shell.
#7
Full Member
Join Date: Dec 2001
Location: FK EPIC FU
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
Empty shell?
Excellent. Well skip the do-it yourself rebuild for the cash you seem willing to spend.
Get an awesome block packaged and ready to fit for your needs. Perhaps you should call mazda trix and discuss your options, and purpose for this car.
When it comes to the ECU and wiring harness on bare bones, you should definitely do your research. Atkins rotary can help you too. They put these power plants into air planes, where failure electrical or otherwise is not an option....so as far as making this work at bare bones, talk to them.
Excellent. Well skip the do-it yourself rebuild for the cash you seem willing to spend.
Get an awesome block packaged and ready to fit for your needs. Perhaps you should call mazda trix and discuss your options, and purpose for this car.
When it comes to the ECU and wiring harness on bare bones, you should definitely do your research. Atkins rotary can help you too. They put these power plants into air planes, where failure electrical or otherwise is not an option....so as far as making this work at bare bones, talk to them.
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post