Well we just bought an RX 7 and the 80 amp fuse keeps blowing after a few seconds I tryed to do some gounding that i saw from another post but it still didn't work. When the fuse was in the interior lights didn't work but then it blew after i jiggled the neg. battery cable and the light can back on. Please help, im running out of ideas.

 

Check the polarity of your battery cables.

 

ok but i think its right

 

Just a quick check. The symptoms you describe are like what happens when the battery poles are switched. but if they are good, you got a problem.

Try disconnecting the alternator and reattching the battery. May have a short in the alt.

Jarrett

 

It's definately a short. Check the positive wires from battery and alt. for any cracks in the insulation. It might be grounding itself and blowing the fuse.

 

If an 80 amp fuse is blowning than its either big time melted wiring or the battery cables are backwards.

Remember the factory ground battery cable is Black/yel, not solid black

 

Well i took the alternator cord off and the fuse stopped blowing but the motor still won't crank and the headlights and radio still don't work, when i turned the key a fan came on but not the one you can see. Thanks for the help so far.

 

Ok. It's like this. You know where the rectangular fuse box is in the engine bay. Now there is a harness running inboard of that fuse box and it goes in a downward direction. About a half foot to a foot from the fuse box should be a black wire with a single blade connector. Pull it apart. Inspect the connector to see if there are any bare spots touching to ground. IF that's good, follow the wire harness from there back towards the crew compartment looking for bare wire touching metal.

The way I understand it, when the key is turned to START, nothing at all happens. No click. Nadda. Right? So it's either that black wire which runs from the fuse box to the ignition key, or the key assy itself. Heck, I can guess as good as anybody.

 

Actually it seems the Alternator was the problem. But the starter should rotate IF the black wire from the 80amp fuse is good to the ignition. I know not what car/year, so here, an 87 start/charge schematic.https://www.rx7club.com/forum/attach...postid=1389325

Check and make sure all the fuses in the crew compartment are intact. They are near the drivers left foot. BUT...if you do not even hear a clicking of a relay when you go to START....I'd be looking at that black wire that feeds the ignition switch and maybe see if the car has a theft device. Food...good. Theft device...bad. Grunt.

 

Damn I am good..

 

****Damn I am good..******J-RAT
As good as you are, and as bad as I am, I'm as good as you are, as bad as I am.

I'd be interesting if 7ormore would write back and let us know if there is any sign of life when he puts the key to the START position when the fuses are installed. If there is no sign of life when going to START we can tell him how to disconnect the right connector prior to his ignition switch and see if there is voltage going to it, or????????? He needs a simple digital meter. Cheap will do, expensive is better.

 

This sounds simmiliar to the Electrical Failure I had 2 weeks ago.

Connector X-23 had intermitently shorted to the brake line and caused the connector to melt and interupt the circut.

 

Sorry for the late reply but yes nothing happens when i turn the key and it does have a security, I have the GLX non-turbo 1988 model. I haven't checked it yet because the car isn't at my house its at my friends house, thanks for the help, im going to check the wire going to the ingition

 

Well i looked at where it connects to the ignition and looked to see if their were any bad spots in the engine but so far it looks ok. I'll take it out later on today.

 

Your still the electrical guru of the 2nd gen section.

I am just wondering why the Alternator was causing the problem. My guess, it had a short, and took some other components out with it.

7ormore, Have you made ECU tester lights yet?

 

Well im an idiot i have the battery cables on the wrong ones and so now pretty much everything works but its still won't crank and i don't know how to make ecu tester light and i don't believe i have a way to check the voltage. Thanks, wow i'm stupid....

 

Oh boy... What did I ask you in the beginning?!?!

YOu have any idea how much damage you could have potentially done to your car?

There are alot of threads here that subject. Do a search, and pray!