2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.
Sponsored by:

88 Gxl na smokes at high rpms

Thread Tools
 
Search this Thread
 
Old 04-02-13, 05:43 PM
  #1  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
88 Gxl na smokes at high rpms

I was wondering since it only smokes at high rpms if I could be anything else besides my oil control rings .?
Old 04-02-13, 06:33 PM
  #2  
Top Down, Boost Up

iTrader: (7)
 
RotaryRocket88's Avatar
 
Join Date: Mar 2008
Location: San Diego, CA
Posts: 8,718
Likes: 0
Received 6 Likes on 4 Posts
The control rings are the most likely culprit. My old NA engine would do the same thing.
Old 04-02-13, 06:38 PM
  #3  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
That's was I was thinking I was wondeeing if it could be anything else looks like I need a rebuild or buy an engine
Old 04-03-13, 10:04 PM
  #4  
Rotary Power

iTrader: (15)
 
wthdidusay82's Avatar
 
Join Date: Sep 2004
Location: Dinwiddie, Va
Posts: 3,706
Received 4 Likes on 4 Posts
Them being bad doesn't mean you need a rebuild, it just means you'll go through oil faster.

Check your engines compression before you decide to get a rebuild and see where you stand.
Old 04-03-13, 11:00 PM
  #5  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
Well I just did an oil change about 500 miles ago and it ate through all that oil already havnt done a compression test yet
Old 04-04-13, 12:22 AM
  #6  
Rotary Power

iTrader: (15)
 
wthdidusay82's Avatar
 
Join Date: Sep 2004
Location: Dinwiddie, Va
Posts: 3,706
Received 4 Likes on 4 Posts
Wow then they must be pretty bad. I was figuring slightly higher consumption but that's much worse.
Old 04-04-13, 07:55 AM
  #7  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
Yea I have to constantly check the oil
Old 04-04-13, 08:19 AM
  #8  
Rotary Power

iTrader: (15)
 
wthdidusay82's Avatar
 
Join Date: Sep 2004
Location: Dinwiddie, Va
Posts: 3,706
Received 4 Likes on 4 Posts
Are you sure you don't have any leaks?
Old 04-04-13, 10:46 AM
  #9  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
That's what I thought but I checked and there was any leaks
Old 04-04-13, 11:22 AM
  #10  
Rotary Power

iTrader: (15)
 
wthdidusay82's Avatar
 
Join Date: Sep 2004
Location: Dinwiddie, Va
Posts: 3,706
Received 4 Likes on 4 Posts
Originally Posted by lazertazer300
That's what I thought but I checked and there was any leaks
How many miles are on the car? I'm sure it must be high. 150k+ range.

What weight oil are you using? I always used 20w50 castrol gtx, unless the temps were very cold in the winter(which depends on where you live).
Old 04-04-13, 11:53 AM
  #11  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
There's Only 86k And It Smoke Crazy At High Rpms
Old 04-04-13, 12:22 PM
  #12  
Rotary Power

iTrader: (15)
 
wthdidusay82's Avatar
 
Join Date: Sep 2004
Location: Dinwiddie, Va
Posts: 3,706
Received 4 Likes on 4 Posts
Originally Posted by lazertazer300
There's Only 86k And It Smoke Crazy At High Rpms
It must of been beaten on and not taken care of well as far as oil changes etc.
Old 04-04-13, 12:28 PM
  #13  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
It Sat For 4 Years The Guy Couldn't Get It Started I Started It And It Drives Amazing Just Eats Oil Like Crazy
Old 04-04-13, 01:38 PM
  #14  
Rotary Power

iTrader: (15)
 
wthdidusay82's Avatar
 
Join Date: Sep 2004
Location: Dinwiddie, Va
Posts: 3,706
Received 4 Likes on 4 Posts
Originally Posted by lazertazer300
It Sat For 4 Years The Guy Couldn't Get It Started I Started It And It Drives Amazing Just Eats Oil Like Crazy
Mine sat for almost a year and it had spun bearings. Mines Turbo, so it was obviously beaten on and not maintained right.

I have a build thread in the builds section if you want to check it out.
Old 04-04-13, 02:03 PM
  #15  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
Alright Yeaa ill check it out I'm sure I need a rebuild or buy one off from a user on here
Old 04-04-13, 02:12 PM
  #16  
Winter Rotary

iTrader: (5)
 
Acesanugal's Avatar
 
Join Date: Dec 2006
Location: Athens, Georgia
Posts: 2,552
Likes: 0
Received 12 Likes on 12 Posts
Let us all be logical for a moment, shall we?

When he says his car burned thru all of that oil, that is likely a bit wrong. Surprisingly, a lot of people do not understand how to check their oil, let alone properly. Between the low and full marks on your dipstick, that only represents roughly a quart of oil inside the engine. It does NOT represent the total amount of oil in the engine .

These are questions that people should be asking the OP before they got spewing ignorant assumptions.

Needs a rebuild? Over what? A little oil smoke at the top of the rev range? That is completely normal for a high mileage factory motor.

One of the 7's I pulled out of a field after years of being inoperable smoked like a freight train for several days worth of driving before it only started smoking around 6500 revs.

Jesus H. Christ, the question about what kind of oil the OP is using is the only reply that is worth a damn.

Sent from my ECU using the Check Engine Light.
Old 04-04-13, 02:29 PM
  #17  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
Ok No One Asked You To Get All Smart Or Be An ******* About The Situation I Know How To Check Oil And I've Talked To People That Actually Rebuild Them And They Also Say I Can Be An Oil Control Ring
Old 04-04-13, 02:55 PM
  #18  
Winter Rotary

iTrader: (5)
 
Acesanugal's Avatar
 
Join Date: Dec 2006
Location: Athens, Georgia
Posts: 2,552
Likes: 0
Received 12 Likes on 12 Posts
Originally Posted by lazertazer300
Ok No One Asked You To Get All Smart Or Be An ******* About The Situation I Know How To Check Oil And I've Talked To People That Actually Rebuild Them And They Also Say I Can Be An Oil Control Ring
Why Do You Feel The Need To Capitalize Every Word In Your Sentences?

Yes, you are correct.. It could very well be the oil control rings as they are the most common cause of oil smoke higher up in the rev range. Now, that being said, if your reading comprehension skills are really that terrible that I have to explain this to you, fine:

I wasn't attacking *you*, I was actually defending you to the ignorant flood of responses.

Don't get your panties in a twist, child...
Old 04-04-13, 02:57 PM
  #19  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
Well I'm Sorry For Responding That Way It Just Seemed The Way You Was Responding It Was Towards Me
Old 04-04-13, 03:01 PM
  #20  
Rotary Freak

iTrader: (4)
 
philiptompkins's Avatar
 
Join Date: Jan 2005
Location: Houston
Posts: 1,523
Likes: 0
Received 0 Likes on 0 Posts
Yeah when you said "all that oil" I was wondering how much you meant. Did you run it till the pan was completely dry? Probably not.
Old 04-04-13, 03:26 PM
  #21  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
No didn't run it til it was dry but it was getting very close had to put 2 quarts in
Old 04-04-13, 04:00 PM
  #22  
Rotary Power

iTrader: (15)
 
wthdidusay82's Avatar
 
Join Date: Sep 2004
Location: Dinwiddie, Va
Posts: 3,706
Received 4 Likes on 4 Posts
Originally Posted by lazertazer300
No didn't run it til it was dry but it was getting very close had to put 2 quarts in
The entire system holds around 4.5 quarts or so.
I guess I shouldn't have went under the assumption that he knows how to read his dipstick. Ace is right it only represents the last quart that tops off the system.

If he ran it until it was actually empty the engine would have no oil pressure , therefor no lubrication, and oil also contributes to cooling the engine so it will not only have no protection to the internals, it will also cause overheating.

Wouldn't take long before engine failure occurs.
Old 04-04-13, 04:12 PM
  #23  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
I understand that you took it to literall that all the oil was gone was just stating that it lost a llarge amount in short time
Old 04-05-13, 03:26 PM
  #24  
Vintage sportcars

 
StevenL5975's Avatar
 
Join Date: Jun 2010
Location: Germany
Posts: 348
Likes: 0
Received 1 Like on 1 Post
My 87 Na did similar thing, used 5 quarts per week ...
Old 04-05-13, 03:31 PM
  #25  
Full Member
Thread Starter
iTrader: (-1)
 
lazertazer300's Avatar
 
Join Date: Feb 2013
Location: michigan
Posts: 77
Likes: 0
Received 1 Like on 1 Post
What did you end up doing rebuild.?


Quick Reply: 88 Gxl na smokes at high rpms



All times are GMT -5. The time now is 08:08 PM.