3mm Rotor question
#1
3mm Rotor question
First, right off the bat, let me say that this is NOT a "How much is this worth?" thread. I am not, at this time, looking to sell them or determine value. Do not tell me to post in the classifieds.
Ok, I have a low compression 85 13b in my basement, collecting dust and staining my floor. I was thinking about parting it out, primarily the 3mm rotors. Is interest for these, or do people prefer milled 2nd gen rotors, due to weight?
I read somewhere that you need the counterweights as well. Is this front and rear, or just heresay?
Ok, I have a low compression 85 13b in my basement, collecting dust and staining my floor. I was thinking about parting it out, primarily the 3mm rotors. Is interest for these, or do people prefer milled 2nd gen rotors, due to weight?
I read somewhere that you need the counterweights as well. Is this front and rear, or just heresay?
#3
talking head
front and rear rotating masses need to move to the new motor with the rotors
if your donor is a manual,, this includes the entire flywheel
and this makes the early rotors a tight fit in later housings at high rpms
the rotor housing inside dimensions change almost imperceptibly tighter between 1985 and 1986
and thus the rotors may require light clearancing on the face if you intend to push 8500 + rpms
i have the pictures ( and housings ) to back that statement up
JHB were very correct when they warned people of the trochoid dimension changes
NB
if you use rx4 1757 front mass it will clash in later 6 port engines with the 6 port runner casting underneath the timing cover
if you use the GSL-SE engine front weight instead it is lipped to clear this
if your donor is a manual,, this includes the entire flywheel
and this makes the early rotors a tight fit in later housings at high rpms
the rotor housing inside dimensions change almost imperceptibly tighter between 1985 and 1986
and thus the rotors may require light clearancing on the face if you intend to push 8500 + rpms
i have the pictures ( and housings ) to back that statement up
JHB were very correct when they warned people of the trochoid dimension changes
NB
if you use rx4 1757 front mass it will clash in later 6 port engines with the 6 port runner casting underneath the timing cover
if you use the GSL-SE engine front weight instead it is lipped to clear this
#4
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,901
Received 2,644 Likes
on
1,873 Posts
front and rear rotating masses (counter weights) need to move to the new motor with the rotors
if your donor is a manual,, this includes the entire flywheel
and this makes the early rotors a tight fit in later housings at high rpms
the rotor housing inside dimensions change almost imperceptibly tighter between 1985 and 1986
and thus the rotors may require light clearancing on the face if you intend to push 8500 + rpms
i have the pictures ( and housings ) to back that statement up
JHB were very correct when they warned people of the trochoid dimension changes
NB
if you use rx4 1757 front mass it will clash in later 6 port engines with the 6 port runner casting underneath the timing cover
if you use the GSL-SE engine front weight instead it is lipped to clear this
if your donor is a manual,, this includes the entire flywheel
and this makes the early rotors a tight fit in later housings at high rpms
the rotor housing inside dimensions change almost imperceptibly tighter between 1985 and 1986
and thus the rotors may require light clearancing on the face if you intend to push 8500 + rpms
i have the pictures ( and housings ) to back that statement up
JHB were very correct when they warned people of the trochoid dimension changes
NB
if you use rx4 1757 front mass it will clash in later 6 port engines with the 6 port runner casting underneath the timing cover
if you use the GSL-SE engine front weight instead it is lipped to clear this
Thread
Thread Starter
Forum
Replies
Last Post
KAL797
Test Area 51
0
08-11-15 03:47 PM