2nd Generation Specific (1986-1992) 1986-1992 Discussion including performance modifications and technical support sections.

2ng Gen wont start after it warms up

Thread Tools
 
Search this Thread
 
Old May 4, 2006 | 08:33 PM
  #1  
jbz12's Avatar
Thread Starter
Junior Member
Tenured Member 05 Years
 
Joined: Jul 2002
Posts: 22
Likes: 0
From: TN
Angry 2ng Gen wont start after it warms up

Help me. I'm goin CRAZY!!!!!!!!!!!!!!!! I got a 2nd gen 86 13b. I tried replacing the coils. The car ran good this winter. Now that it is warming up, after driving the car for a while. Starting and stopping, etc. The car won't start. If I let it cool for a few hrs, it fires right up. I tried buying new coils, not new igniters, and it worked fine for the winter. Now summer is here and after it warms up and you shut it off... nuthin! Let it cool for a few hrs and it fires right up. Any ideas would be helpful!


Thanks,

Jim
Reply
Old May 4, 2006 | 08:41 PM
  #2  
1SxyRXy's Avatar
my fc broke
Tenured Member 20 Years
 
Joined: Feb 2003
Posts: 2,231
Likes: 0
From: rohnert park,CA/ bay area
leaky injectors/low compression
Reply
Old May 4, 2006 | 08:45 PM
  #3  
Russ-R's Avatar
Full Member
Tenured Member 05 Years
 
Joined: Dec 2004
Posts: 226
Likes: 0
From: Georgia
check for bad grounds
Reply
Old May 4, 2006 | 08:50 PM
  #4  
walken's Avatar
Registered Loser
Tenured Member 05 Years
iTrader: (6)
 
Joined: Dec 2002
Posts: 2,224
Likes: 0
From: Whiterock
you could also try changing your plugs
Reply
Old May 17, 2006 | 09:29 PM
  #5  
jbz12's Avatar
Thread Starter
Junior Member
Tenured Member 05 Years
 
Joined: Jul 2002
Posts: 22
Likes: 0
From: TN
I have replaced the plugs and have fresh wires. The injectors check good. Someone once told me about cleaning the engine by spraying some kind of cleaner in the air intake while motoring the engine with the fuel pump fuse pulled. You let it sit for about 30 mins and start the engine. This is supposed to clean out the carbon buildups.

Has anyone heard of this? Also is there a good way check the igniters before replacing them? I have a manual but don't see anything regarding this.

Thanks,

Jim
Reply
Old May 17, 2006 | 09:46 PM
  #6  
rurouni2071's Avatar
wanderer
Tenured Member 15 Years
 
Joined: Jun 2005
Posts: 182
Likes: 0
From: 100 Mile House , BC , Canada
mine did the same thing ... then one day it would onlt run for 15 minutes and shut off ..... then I parked it and left it for a week .. after that it would only run for 5 seconds.. now nothing ... I did a compression test today with a piston tester .. it was a cheap one and I couldnt remove the check valve , but I figured that it would still give at least a shot in the dark.... it came out at 52 psi .................. I am currently drunk ..... I bought it in october and have only driven it a month .... when i bought it it showed 110 psi .... still havent even finished paying it off ...... .. supposedly it only had 60 000 km on a rebuild ... 9 grand , flush

Last edited by rurouni2071; May 17, 2006 at 09:50 PM. Reason: fogot to mention
Reply
Old May 18, 2006 | 10:32 PM
  #7  
Julius's Avatar
Newbie
 
Joined: May 2006
Posts: 3
Likes: 0
From: Melbourne
could be a water seal :!:
Reply
Old May 18, 2006 | 11:19 PM
  #8  
Denholm's Avatar
Not a rotor? Not a motor.
Tenured Member 05 Years
 
Joined: Dec 2005
Posts: 185
Likes: 0
From: BC, Canada
compression test
Reply
Old May 19, 2006 | 07:50 AM
  #9  
HAILERS's Avatar
HAILERS
Tenured Member 10 Years
 
Joined: May 2001
Posts: 20,563
Likes: 27
From: FORT WORTH, TEXAS,USA
Make a fuel cut switch as shown in these threads: https://www.rx7club.com/forum/search...archid=1949110
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Kyo
2nd Generation Specific (1986-1992)
6
Apr 13, 2019 09:24 AM
stickmantijuana
Microtech
30
Apr 23, 2016 06:37 PM
1993fd3sracer1
3rd Generation Specific (1993-2002)
29
Oct 13, 2015 01:57 PM
1993fd3sracer1
1st Generation Specific (1979-1985)
20
Sep 7, 2015 11:50 AM
gtcd
1st Generation Specific (1979-1985)
30
Aug 19, 2015 02:44 AM




All times are GMT -5. The time now is 01:01 PM.