Those looking for the led S5 lights.
#1
Those looking for the led S5 lights.
Found a couple sets while combing through all 5300 items listed on yahoo japan auctions... sadly not what I was looking for. $250-380 +deputy fees and shipping
RX7 FC3S 後期 6連リン゠°ã€€ãƒ•ãƒ«ï¼¬ï¼¥ï¼¤ãƒ†ãƒ¼ãƒ«ã€€ - ヤフオク!
or
RX-7 FC3S
RX7 FC3S 後期 6連リン゠°ã€€ãƒ•ãƒ«ï¼¬ï¼¥ï¼¤ãƒ†ãƒ¼ãƒ«ã€€ - ヤフオク!
or
RX-7 FC3S
#4
I break Diff mounts
iTrader: (1)
I made a set for myself and then a couple of friends. Haven't made any in the last few months.
I make the boards myself since it's not worth doing a batch run of these board in large numbers. I got a cnc machine recently and plan on using it to make "prettier" versions
A shot on George's FD car.
Video I made of my prototypes on my car. The turn signal halo is now turn signal only. Not on with running lights
I make the boards myself since it's not worth doing a batch run of these board in large numbers. I got a cnc machine recently and plan on using it to make "prettier" versions
A shot on George's FD car.
Video I made of my prototypes on my car. The turn signal halo is now turn signal only. Not on with running lights
#5
Bridge Burner.
iTrader: (13)
I made a set for myself and then a couple of friends. Haven't made any in the last few months.
I make the boards myself since it's not worth doing a batch run of these board in large numbers. I got a cnc machine recently and plan on using it to make "prettier" versions
A shot on George's FD car.
Video I made of my prototypes on my car. The turn signal halo is now turn signal only. Not on with running lights
Video Link: https://www.youtube.com/watch?v=bqp3Uoq51dI
I make the boards myself since it's not worth doing a batch run of these board in large numbers. I got a cnc machine recently and plan on using it to make "prettier" versions
A shot on George's FD car.
Video I made of my prototypes on my car. The turn signal halo is now turn signal only. Not on with running lights
Video Link: https://www.youtube.com/watch?v=bqp3Uoq51dI
Trending Topics
#14
I break Diff mounts
iTrader: (1)
I'm working on some that I can make easily. Mine are all hand made and etched so it's a total pain and not as good quality wise.
I'm in the process of reworking it to use my cnc machine to do the hard work.
Still in the initial stages. Code is almost ready for the led side. Working on making the power distribution board next. Then I'll make a little plexiglass enclosure to hold it.
Test cut in some plexi to see if it was cutting right. CNC's can be a bitch to get calibrated.
I'm in the process of reworking it to use my cnc machine to do the hard work.
Still in the initial stages. Code is almost ready for the led side. Working on making the power distribution board next. Then I'll make a little plexiglass enclosure to hold it.
Test cut in some plexi to see if it was cutting right. CNC's can be a bitch to get calibrated.
#15
★*NGTDRV★*
iTrader: (16)
I'm working on some that I can make easily. Mine are all hand made and etched so it's a total pain and not as good quality wise.
I'm in the process of reworking it to use my cnc machine to do the hard work.
Still in the initial stages. Code is almost ready for the led side. Working on making the power distribution board next. Then I'll make a little plexiglass enclosure to hold it.
I'm in the process of reworking it to use my cnc machine to do the hard work.
Still in the initial stages. Code is almost ready for the led side. Working on making the power distribution board next. Then I'll make a little plexiglass enclosure to hold it.
Thanks for keeping us updated!
#19
I break Diff mounts
iTrader: (1)
Sorry dudes, Been crazy busy with building an FD.
Took the job of putting it back together in May and have had serious road blocks (Blown motor...) About to get it running again and will have free time to get back on the tails.
My Benchtop CNC was being a bitch too. Stupid amounts of backlash causing it not not be accurate enough for the small pcb traces. I did a bit of adjusting and hopefully I removed enough to get some neat traces out of it.
Here's a tip for CNC hobbyists. Sub $1k CNC machines need a lot of work before they work well.... ughh
Street ported motor with new T2 housings
GT4088 turbo
Simplified efi harness
ID 1000 Primaries
ID 2000 Secondaries
Full Function Engineering Fuel rails
AEM 340lph pump
PFC
Took the job of putting it back together in May and have had serious road blocks (Blown motor...) About to get it running again and will have free time to get back on the tails.
My Benchtop CNC was being a bitch too. Stupid amounts of backlash causing it not not be accurate enough for the small pcb traces. I did a bit of adjusting and hopefully I removed enough to get some neat traces out of it.
Here's a tip for CNC hobbyists. Sub $1k CNC machines need a lot of work before they work well.... ughh
Street ported motor with new T2 housings
GT4088 turbo
Simplified efi harness
ID 1000 Primaries
ID 2000 Secondaries
Full Function Engineering Fuel rails
AEM 340lph pump
PFC
#20
Sharp Claws
iTrader: (30)
My Benchtop CNC was being a bitch too. Stupid amounts of backlash causing it not not be accurate enough for the small pcb traces. I did a bit of adjusting and hopefully I removed enough to get some neat traces out of it.
Here's a tip for CNC hobbyists. Sub $1k CNC machines need a lot of work before they work well.... ughh
it's easy to spend $1k and still need to work out minor bugs but it's always best to start with a good machine and the Denford is very good for small intricate work. fine tuning is such a royal pain in the ***. the machine actually worked flawlessly but setting it up, converting images to code and making adjustments took a few weeks.
Last edited by RotaryEvolution; 10-21-13 at 05:54 PM.
#24
I break Diff mounts
iTrader: (1)
Hey dudes, I'm back with an update.
Ditched doing it on CNC. Wasn't going to be precise enough.
Decided to learn how to make a board that can be sent off for prototyping.
Once I get them in the mail. I'll wire them together and see if I screwed anything up.
Sneak peak
Ditched doing it on CNC. Wasn't going to be precise enough.
Decided to learn how to make a board that can be sent off for prototyping.
Once I get them in the mail. I'll wire them together and see if I screwed anything up.
Sneak peak