1.3 n/a in an rx7? NOt possible
02-24-08, 07:55 PM
#2
Rotary Enthusiast
Thread Starter
iTrader: (1)
Join Date: Mar 2007
Location: sc
Posts: 817
Likes: 0
Received 0 Likes
on
0 Posts
More pics
Here are a few more pics. The guy pissing on my car is one of those guys that drives a honda. Damn haters. The red car in the storage room is an 87 turbo II that im robing from(my parts car) I know your like"why the hell! well, I ordered the wrong engine because the guys said it would work. Dammit, so I got the gxl with a bad rotor and decided to give it a secound chance at life). In the pics I am installing my clutch type turbo II rear end. Now I see why you cant run the n/a driveshaft. Damn thing is a tooth pick next to the turbo. To change out the rear ends you will need a 15mm, 14mm, 17mm, a 13/16 because my mm tool selection is minimal, a half in drive ratchet, and a few other tools I cant remember off the top of my head. First I took off the rear sway bar. Then disconnected the brakes, driveshaft, struts, ebrake cables, etc. Then I took out the 4 mounting points for the diff and the frame. Plop. It was out. Putting it back in was a breeze after the three attempts that were unsuccesful. The only real hang up I had was I couldnt get all the bolts to line up for the 4 mounting points. If you look at the picture out the rear end where the diff hooks into the driveshaft, there are a few bolts that you HAVE to take loose/out to get the 4 mounting points to line up. I will take some up close pics of this next time I work on my car so that noone who looks at this thread will ever have to go through what I went through. 
Stay tuned people. Soon to come is my jdm turbo engine/ tranny install. I already installed the OS Giken super single clutch and flywheel with the act counter so I dont have any pics, but if anyone needs any info on clutch installs, hit me up.
Stay tuned people. Soon to come is my jdm turbo engine/ tranny install. I already installed the OS Giken super single clutch and flywheel with the act counter so I dont have any pics, but if anyone needs any info on clutch installs, hit me up.
Trending Topics
02-24-08, 08:27 PM
#9
Newbie
Join Date: Apr 2007
Location: montreal
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
hi my name is dinster and own a 1990 rx-7 convertible non turbo
my rear rotor blew want to install turbo charged engine stock ! is
it possible i can get a complete engine and trany it comes with ecm and
complete harness is it possible to do im planning to do this at hom e
please reply as soon as you can thanks
my rear rotor blew want to install turbo charged engine stock ! is
it possible i can get a complete engine and trany it comes with ecm and
complete harness is it possible to do im planning to do this at hom e
please reply as soon as you can thanks
02-24-08, 08:40 PM
#10
Rotary Enthusiast
Thread Starter
iTrader: (1)
Join Date: Mar 2007
Location: sc
Posts: 817
Likes: 0
Received 0 Likes
on
0 Posts
dinster, the best advice for me to give to you is check out rotaryresurrection.com look in the tech section. He has everything you need to know in there
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
ncds_fc
New Member RX-7 Technical
1
08-15-15 10:06 AM