Putting new rims on
#1
Can Post Only in New Member Section
Thread Starter
Join Date: Aug 2018
Location: Baker City, Oregon
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
Putting new rims on
Im getting 17x8 +35mm in the front, and 17x9 +40mm in the back, would those rims look good on my 87 fc? If so, what type of tires should i put on them for drifting.
#2
Junior Member
I would imagine those would look good as long ad you’re running the right suspension setup. As far as tires for drifting, I would suggest just buying used tires so you can just burn whats left of them off unless you have money to afford a brand new set of tires each week.
#3
Can Post Only in New Member Section
Thread Starter
Join Date: Aug 2018
Location: Baker City, Oregon
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
I would imagine those would look good as long ad you’re running the right suspension setup. As far as tires for drifting, I would suggest just buying used tires so you can just burn whats left of them off unless you have money to afford a brand new set of tires each week.
#5
I have a rotary addiction
iTrader: (18)
Its all about your alignment settings and tire choice when fitting new suspension and wheels. If you run close to factory recommended 0.0* front camber with 17x8 +35 and about a 225 tire you will be pretty close to "factory-flush" with no need to roll fenders or modify anything. If you run a bit of negative camber (-1.0* to -2.0*) you will probably want a lower offset wheel (like maybe +10 to +20) with a 17x8 and 225 tire. People are going to say "But you can fit huge wheels in there and slam it and stance it out etc", but being an alignment technician I hate the thought of stanced cars with massive wheels that scrape the ground and bounce around town like they're on pogo stick suspension.
For the original setup you posted, front should be OK, but in the rear I would go a bit lower on offset to match the front with the setup you posted. You may want to invest in some camber adjusting links to fine tune your rear alignment to perfect the look of the new wheels. Most FCs have -1.5* to -2.0* camber in the rear. Preferred is somewhere closer to -0.5*. Toe is adjustable from factory, but chances are the cam bolts are seized in the lateral arm bushings, so you will probably want to get adjustable toe links as well.
FYI
ALWAYS do an alignment after any suspension or steering repair. The smallest differences in any part can make huge difference in how your car drives and looks. Remember you can rotate the strut tops to change camber and caster by about 0.5* either way.
For the original setup you posted, front should be OK, but in the rear I would go a bit lower on offset to match the front with the setup you posted. You may want to invest in some camber adjusting links to fine tune your rear alignment to perfect the look of the new wheels. Most FCs have -1.5* to -2.0* camber in the rear. Preferred is somewhere closer to -0.5*. Toe is adjustable from factory, but chances are the cam bolts are seized in the lateral arm bushings, so you will probably want to get adjustable toe links as well.
FYI
ALWAYS do an alignment after any suspension or steering repair. The smallest differences in any part can make huge difference in how your car drives and looks. Remember you can rotate the strut tops to change camber and caster by about 0.5* either way.
Last edited by NCross; 09-17-18 at 06:31 PM.
#6
Junior Member
For drifting, buying quality tires upfront and ebay cheap bois in the rear. DONT buy used tires. Its a waiste of time to get them balanced and mounted to only need another set even sooner than cheap tires.
Thread
Thread Starter
Forum
Replies
Last Post
Ocelot
Suspension/Wheels/Tires/Brakes
4
03-01-04 01:32 PM
LethalRX7
2nd Generation Specific (1986-1992)
3
04-16-02 06:58 PM