Were can i buy a set of 2?

Thanks in advance

/Brad

 

lol, they aren't cheap anywhere, try to find some used ones, otherwise, the ground crontrols are about 260 a pop, available at mazdatrix and some other places.

 

Damn, any1 have used 1's?

 

I just got a set of FC plates that im going to use on my FB. Got mine for little under $5 and a FC strut bar for a little under $10. Couple of mods and they should fit nice. Just got to know were to shop and what to search for.

 

seanot, care to share where you found them? It took me a month of searching to get what you got for just over 100 bux, how did you get it for 15?

Alvin

 

i havent looked into doing this seriously but i've heard of people cutting slots in their strut towers, how's that for cheap?
i have 0% of an idea as to why this is/is not a viable replacement for camber plates however.
anyone care to inform?

 

Course I have been looking for a little over 7 monthes now. Bid on a couple that were about $50 but alway got out bid. Found a set for 500 yen, put a bid on them and went to sleep. Woke up checked and found out I won at 500 yen. Just lucky no one else saw the auction.

General seach
http://list1.auctions.yahoo.co.jp/jp...-category.html

RX7 camber search

yahoo auctions

Strut Bars FC

Yahoo auctions

 

I will build you some custom pieces at $150 a set.
PM if interested. I will be starting a set for a Rx3 in a few days. I can through your's in the mix.

-billy

 

Awesome, ill let you know if i dont find any used 1's for cheap.

 

I can't read japanese

 

Hey bwaits, I'm interested, got any pix, email me at aussiesmg@yahoo.com

My Aussie mechanice build his by reinforcing the strut tower tops by welding in thicker metal replacements and then slotting them, but the factory tops are not strong enough, they will bend under the loads of serious springs and track days.

 

No pics, just a design in my head. I will have some cad stuff here in the next few days. I will post it up then.

-billy

 

Cool

 

surely that's cheaper than camber plates.
so why are we all buying these again?

 

A few reasons I can think of would be:

1) Some race classes do not allow you to "Reinforce" anything. So the plates bolt in and allow for adjustment but will also end up adding to the strength of the thin sheet used as stock.

2) Any good set of camber plates are also going to design in a change in caster as well. You would need to slot the holes for and aft to get caster. Now your holes are so big you need fat *** washers and most of the strut top is now gone.


-billy

 

Any pics today? CAD roughs?

 

is it wise to use cheap camber plates? im not knowledgeable about this but doesnt it hold your whole strut together?

 

i think cheap mostly meant used, not bad ones... how's the car running peter? havn't seen you in a few weeks.

 

haha, im good. i was planning to swap my gs front brakes to -se's. but now that i just saw the 5 lug big brake kit on the group buy, im gonna get that instead. just checking on this thread cuz when i get wheels, i might need to get camber plate too.

 

Hmmmmmmmmmm. Pics?

 

Here we are. These are draft models. First picture is the First generation parts, second picture is of the rx3 parts and the third is a picture of just the slider. I will have rx2 and Second generation modeled by the end of the week.

I am staring one pair of the first gen and rx3 early next week. Anyone who wants to get in at $150 per pair of this run should speak up. Depending on interest we may launch a group buy.

Kit comes with the plates, bearings, thrust bearings, spacers and hardware needed. These will work with stock upper spring perch or most aftermarket perches.

-billy

 

I am going to already get the brake kit from you. I can only do so much at one time. How long will this GB be available?

 

yeah im drained for cash. im finding a way to come up with the money for the big brake up grade though. if the camber plates are available in about a month id be very interested. i might be able to even come pic them up since youre not too far away, but i dont know. id definately suggest a group buy. advertise it first to check interest though

 

those camber plates looks appealing to me. keep an update!

 

where did you get that pillow joint/slider or are you making those to, im doing a custom job with complete 2nd gen struts on my first gen, just wondering where and how much just the sliders cost
thanks

Paul