Were can i buy camber plates for Cheap?
Joined: May 2004
Posts: 1,366
Likes: 10
From: Drifting a Roundabout near you!
Very interested, make a plate for people to attach a strut brace while you go the software fired up. Send out a update when you want to do a group buy.
lightened fb
Joined: Aug 2004
Posts: 480
Likes: 0
From: vancouver, bc
Originally Posted by Slammed_GSL
Very interested, make a plate for people to attach a strut brace while you go the software fired up. Send out a update when you want to do a group buy.
Joined: May 2004
Posts: 1,366
Likes: 10
From: Drifting a Roundabout near you!
Originally Posted by autopaul
you can attatch a strut brace to basically any camber plates, im almost posetive it wont interfere especially the ones he is desinging, maybe if it was mounted on top of the strut towers, but it shouldnt be a problem
Definitely sounds good billy!
My question is will they work with the Tokico Hp Shocks (blue ones) most guys around here use.... they are direct stock replacements.
My resaon for asking is because other kits require a special shock because of the bearing on the top of the c-plates
My question is will they work with the Tokico Hp Shocks (blue ones) most guys around here use.... they are direct stock replacements.
My resaon for asking is because other kits require a special shock because of the bearing on the top of the c-plates
Parts have been made and went out for powder coating.
I should have them back soon and I will post up some pictures.
We have design these to accept up to a 5/8 shock shaft. We will provide a spacer for stock diameter struts. As well as most any other shock if the purchaser tells us what the size of the shaft is.
These will work with stock upper spring seats or most aftermarket ones for 2.5" coil over springs. They have needle bearing washers underneath so the steering does not rotate the shock shaft.
These will mount without cutting the chassis. You will need to trim a bit to use all of the camber adjustment available, but not for the street.
We have rx3, first generation and second generation models.
-billy
I should have them back soon and I will post up some pictures.
We have design these to accept up to a 5/8 shock shaft. We will provide a spacer for stock diameter struts. As well as most any other shock if the purchaser tells us what the size of the shaft is.
These will work with stock upper spring seats or most aftermarket ones for 2.5" coil over springs. They have needle bearing washers underneath so the steering does not rotate the shock shaft.
These will mount without cutting the chassis. You will need to trim a bit to use all of the camber adjustment available, but not for the street.
We have rx3, first generation and second generation models.
-billy
so basically you can use them on the street, but no-cutting chassis needed unless setting the car up for the track...
And will work with fatcory replacement shocks with a spacer.... Awesome.... If all the info I wrote is correct, I am very interested! Is there a possibility of another group buy?
I must say you do excellent work over there!! This will be the third product I'll buy off you guys this year! (oil pedistal, big brakes... camber plates!!) You gotta get some decals made in slip them in the packaging!! LOL
Talk to ya soon!
And will work with fatcory replacement shocks with a spacer.... Awesome.... If all the info I wrote is correct, I am very interested! Is there a possibility of another group buy?
I must say you do excellent work over there!! This will be the third product I'll buy off you guys this year! (oil pedistal, big brakes... camber plates!!) You gotta get some decals made in slip them in the packaging!! LOL
Talk to ya soon!
Just a quick question... would re-speed ever get into making manifolds? Meaning exhaust manifolds.... I am seeing more and more guys going turbo, but the N/A guys need a spacer made or a entire manifold made to clear the n/a lower intake manifold.
That is to fit up a stock t2 turbo up, this is just a suggestion/question, not actually sure if there would be a market for this, or if you guys would even bother with that.
Here is a bad pic showing what I mean....
it's basically 2 plates with 2 tubes all welded up....
That is to fit up a stock t2 turbo up, this is just a suggestion/question, not actually sure if there would be a market for this, or if you guys would even bother with that.
Here is a bad pic showing what I mean....
it's basically 2 plates with 2 tubes all welded up....
Last edited by JIMMY54; Oct 5, 2005 at 01:35 PM.
Originally Posted by Hyper4mance2k
hot item! is there a definate price yet?
Originally Posted by JIMMY54
so basically you can use them on the street, but no-cutting chassis needed unless setting the car up for the track...?would re-speed ever get into making manifolds?
No cutting on chassis until you need major negative camber (More than you will ever need for the street - Or - Most setups on the track). Will mount upto stock shaft size.
Are you looking for just 2 plates with tubes welded or something that moves the turbo more?
Originally Posted by bwaits
I will build you some custom pieces at $150 a set.
PM if interested. I will be starting a set for a Rx3 in a few days. I can through your's in the mix.
-billy
PM if interested. I will be starting a set for a Rx3 in a few days. I can through your's in the mix.
-billy
Yeah, Im interested. Let me know $$$ when the RX-3 stuff is ready.
Originally Posted by bwaits
No cutting on chassis until you need major negative camber (More than you will ever need for the street - Or - Most setups on the track). Will mount upto stock shaft size.
Are you looking for just 2 plates with tubes welded or something that moves the turbo more?
Are you looking for just 2 plates with tubes welded or something that moves the turbo more?
As for the spacer, yes the 2 plates with the tubes welded.... I know there are afew guys wanting to turbo their cars.... mostly the 12A guys. Re speed should look into this, the second gen guys would get in on that aswell! Research the board and see if it would be worth while.
I'll continue to check back to see when this group buy will start!
Originally Posted by wrxracer55
The struts I am planning on using are the tokico improved touring struts with a bearing OD of .588". Will you be able to accomodate this?
-billy
Parts have been completed and are at the powder coater. They have been taking a long time on this batch. They said they would have them done this week.
I have an rx3 set sold.
wrxracer55 and aws140 want a first gen set each.
wackyracer wants an rx3 set.
These are what I have for possible sold first run units.
We will see how this goes and maybe launch a group buy after those sets are accounted for.
-billy
I have an rx3 set sold.
wrxracer55 and aws140 want a first gen set each.
wackyracer wants an rx3 set.
These are what I have for possible sold first run units.
We will see how this goes and maybe launch a group buy after those sets are accounted for.
-billy
i need a 20b in my fb
Joined: Sep 2005
Posts: 160
Likes: 0
From: Quahog Rhode Island
im a machinest by trade and run cad and pantograph milling machines and also have a bridgeport machine and surface grinder i can make those easy. ive been planning on making them for my car i didnt realize so many people need them. ill put some pics up in a few months when i get around to it.
i need a 20b in my fb
Joined: Sep 2005
Posts: 160
Likes: 0
From: Quahog Rhode Island
Originally Posted by bwaits
Here we are. These are draft models. First picture is the First generation parts, second picture is of the rx3 parts and the third is a picture of just the slider. I will have rx2 and Second generation modeled by the end of the week.
I am staring one pair of the first gen and rx3 early next week. Anyone who wants to get in at $150 per pair of this run should speak up. Depending on interest we may launch a group buy.
Kit comes with the plates, bearings, thrust bearings, spacers and hardware needed. These will work with stock upper spring perch or most aftermarket perches.
-billy
I am staring one pair of the first gen and rx3 early next week. Anyone who wants to get in at $150 per pair of this run should speak up. Depending on interest we may launch a group buy.
Kit comes with the plates, bearings, thrust bearings, spacers and hardware needed. These will work with stock upper spring perch or most aftermarket perches.
-billy
