thafox

i just bought this off a friend, he's getting them made by the bunches here, it's so freaking awsome, i dont think pic's do it much justice

mazdaverx713b

iTrader: (91)

i like the rotor ****. looks kinda bulky though. its hard to tell from the pictures.

Jhereg

iTrader: (27)

I was really tempted, but I prefer the shape and feel of the stock one. Might get a nice leather wrapped later. Nice looking though. Love the rotor one too.

Lock & Load

Some guys here in OZ USE THESE ONES


CorkSport for cheap Mazdaspeed leather gearknobs.

These are actually heavier than the stock gearknob, awesome for use with a short shifter (or a stock one). "Mazdaspeed" embossed on the side as pictured, and shift pattern on the top of the ****.



$99USD plus shipping (around $15)!!

http://www.corksport.com/mazdaspeed-...shift-kit.html

Jibaro 12A

iTrader: (8)

I love my original S2 shifter way too much! But if I had to chose I'd take the rotor one too!

Jeezus

iTrader: (4)

Swapped mine for one from a Honda. Same thread pitch, but the threads are way high up in the
**** compared to stock, I would say it lowered the top by about half an inch.

ΝΙΚΟΣ

this is what i use on my cars...illuminated rx8 *****...great shape and handling..

ty97206

Where do you get that **** at?

Crispin38

iTrader: (3)

I have a miata **** and shifter. It's out of 97 model. Wouldn't ever change.

patmac6075

iTrader: (26)

I agree with Mazdaverx....at least in the pix it looks a tad bulky....I'd like it to be about 25% smaller. Then I'd get one,

zaridar

iTrader: (3)

I want one!!!

pjr

iTrader: (8)

I tried to put an after-market shift **** on my stock SE shifter and had no success. I cannot figure out what size and pitch fits the stock shifter. They send me a metric 10 and a 12 but neither fit. I went to the hardware store with the stock **** and I couldn't figure out what bolts fit it

Anyone have tips on what they did to get aftermarket products to fit?

pjr

iTrader: (8)

From a Honda? Really? What model is the same as a 1st gen RX7?

Jhereg

iTrader: (27)

out with stock... wanted the rx8 one but too spendy. love the look and feel of this one.

Marx-7

Had the luck of getting one from a friend who used to work for a local Mazdadealer and used it in my FC. Looked and felt great especially illuminated but had to get used again to the shifting because the leaver gets shorter..

pjr

iTrader: (8)

And it fits the FB?

Marx-7

I think not. I had to (don't know the exact english word for it so correct me) drill it out just a little bit to get it correct for the FC shifter. I think the size leaver of the FB and the FC are the same atleast for the european cars.

thafox

yea it's a factory -se tranny i've got in there

hoang5659

iTrader: (14)

any word on where we can get one of these shift *****? i like the rotor one alot.

thafox

he's been selling them on ebay here's a link to his stuff http://cgi.ebay.com/ebaymotors/mazda...Q5fAccessories

misterstyx69

iTrader: (142)

Full Cruise on Forum is selling the **** that the OP has pictured.
https://www.rx7club.com/showthread.p...highlight=****

thafox

yes he is but he's still getting them from my friend down here, i notified my friend when i 1st saw that and he acknowlaged that he was sending my friend questions and had purchased a few from him

MacNeil

If you dont mind me asking, where did you pick up that aftermarket console kit? I got one from bestkits.com and it was total garbage.

Jhereg

iTrader: (27)

no kit... If you're meaning the 2 shelf unit, it was in a replacement bezel I grabbed off a guy to replace my orig that was broken. Just tossed them in so it wasn't an empty din.