HOLY exhaust can it cause......
05-23-06, 12:09 AM
#26
awsome torchiod i have a header sittin just need gaskets for the engine and end of the header and the cheapest shop i have found is 300 for a straight thro with a new muffler but since i aint got a dime the old muffler will do i spose
ill try take the pre cat off tomorro and see what happens
aussiesmg
ild say month ago when i put my carter in
i emptyed my tank and kept pouring gas in there to try flush it abit
was very minor dust in there i was happy
ill try take the pre cat off tomorro and see what happens
aussiesmg
ild say month ago when i put my carter in
i emptyed my tank and kept pouring gas in there to try flush it abit
was very minor dust in there i was happy
05-23-06, 12:13 AM
#27
Originally Posted by 84RX_Se7en
A broom handle cut in half is your friend if you take the exhaust apart and ram it through the cat and from the back of the muffler to the tips. Empty the cat and muffler of anything. It'll be louder but the plugging problem will most likely be gone. That or a snake used in plumbing. If you can feed that through the headers/downpipe, pre-cat, and cat as well as the muffler.
well im lookin down the cat now it has like a oval aluminuim thing inside i doubt a broom could break it
time for a drill and to go primal on this cat
"that ******* cats back"
hay ausie did you ever go to a kevin bloody wilson show?
05-23-06, 12:20 AM
#31
Originally Posted by trochoid
300, ouch, but then I do my own. If you're going headers, you will need a pre-silencer/mid-muffler. If you have been following the thread on the the Borla, go that route when you can afford it for a mid-muffler.
ill check that thread out but for the mean time i can just run a straight tho and put up with the exsesive noise "ill have too
"then later get a shop to add the aditional bola etc??
05-23-06, 12:37 AM
#33
hehe i have been for 2 weeks now since my cat started to fart alot
is borla a expensive brand new
hehe i just looked you up on the map lol it would take at least a week to drive
whats best under or over axel?
ill consider rb springs later iv heard people with 3" under axel and it dont scrap what you think scott
is borla a expensive brand new
hehe i just looked you up on the map lol it would take at least a week to drive
whats best under or over axel?
ill consider rb springs later iv heard people with 3" under axel and it dont scrap what you think scott
05-23-06, 01:08 AM
#36
It will be cheaper to install the header now, straight pipe from there, then add a mid muffler later. Black Dragon has the big exhaust gasket for 15, if you have a single outlet header, get a stock sized metal faced gasket. If dual, buy the collector, flange and gasket.
I personally hate to pay for doing the same thing twice.
I personally hate to pay for doing the same thing twice.
05-23-06, 10:24 PM
#37
maybe you didnt understand my kiwi english
it has been stated a few times in threads that a rb header with a collector"2pipe-1pipe"
which is what i have
will fit the stock exhaust system so what i was askin is after the stock manifold conection there is another conection then it goes to the pre cat conection then cat converter etc
so im guessing the header should fit to that second joint because of the angle lenght etc
so in other words i could put the header on when i get gaskets
i know whart your saying it would be better to do the whole thing
but the american cops are ******* from my once experince and a loud exhaust ticket cost over 300$
thats a new exhaust in fines lol
i hope that makes sence
just trying to get my question across mate. no worrys
scott your allways helpfull and i really apreciate it
it has been stated a few times in threads that a rb header with a collector"2pipe-1pipe"
which is what i have
will fit the stock exhaust system so what i was askin is after the stock manifold conection there is another conection then it goes to the pre cat conection then cat converter etc
so im guessing the header should fit to that second joint because of the angle lenght etc
so in other words i could put the header on when i get gaskets
i know whart your saying it would be better to do the whole thing
but the american cops are ******* from my once experince and a loud exhaust ticket cost over 300$
thats a new exhaust in fines lol
i hope that makes sence
just trying to get my question across mate. no worrys
scott your allways helpfull and i really apreciate it
Last edited by blwfly; 05-23-06 at 10:28 PM.
05-23-06, 10:46 PM
#40
The headers will replace the 2 pre-cats. How it mates with the main cat varies with the type of header. If you have the dual outlet headers, you need the collector and flange, then decide if you want to run duals to the axle or single pipe it right after the header.
If noise tickets are that expensive, you WILL need a pre-silencer of some sort. If you can't afford a Borla now, at least stick a cheap glasspack in there until you can afford the Borla.
If noise tickets are that expensive, you WILL need a pre-silencer of some sort. If you can't afford a Borla now, at least stick a cheap glasspack in there until you can afford the Borla.
05-23-06, 11:01 PM
#43
Originally Posted by J_Mart
Hey dude, I work at a mazda dealership and we can sell those exhaust gaskets for about 12-15 bucks too
are they usally in stock?
theres a mazda dealer not to far away would they have the header gasket? of is the stock gasket diff
i wouldnt mind paying a lil more if it close
05-23-06, 11:24 PM
#46
Mostly play with 1st gens. The widebody is in the following thread.
https://www.rx7club.com/build-threads-293/unvieling-12a-bp-widebody-462184/
https://www.rx7club.com/build-threads-293/unvieling-12a-bp-widebody-462184/
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM