2005 rx 8 13b motor swap into first gen rx7
#1
Junior Member
Thread Starter
Join Date: Jun 2007
Location: osgoode/canada
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
2005 rx 8 13b motor swap into first gen rx7
well just wondering if its possible to put in this motor in 05 rx8 13b .. i can get one very cheap,, but i would like to stay carbed.. Can it be done??? or should i just pass on the swap??
#2
Wheel Revolutionist!
Anything can be done if throw enough money at it! If you can get it cheap throw a carb on it and go! You would have to hook up linkage for the accelerator as the Renesis have electronic throttle response.
#5
Eats, Sleeps, Dreams Rotary
Join Date: Jul 2004
Location: Allentown, PA - Paterson, NJ
Posts: 3,247
Likes: 0
Received 2 Likes
on
2 Posts
Not that difficult. The only "hard to find" part would be the intake and header, if you go that route. The motor itself if you can find one would be the most expensive part. The rest should be easy.....sorta.
#6
Good at "stupid"
Why not just use rx-8 rotating assembly with 4 port 13b housings and irons? Then you can just carb it.
Or if you want to be really ghetto use 12a irons and 13b housings with rx8 internals...LOL!
Or if you want to be really ghetto use 12a irons and 13b housings with rx8 internals...LOL!
#7
premix, for f's sake
iTrader: (6)
the ecu controls the ignition and the omp, so youll also have to find a way around that. you could run 2-stroke premix and eliminate the omp, but im not sure if a distributor can be used w/ the renesis motor.
so far the only renesis swap ive seen in a first gen actually retained all of the rx-8's fuel injection and engine controls...looked like an rx-8's engine bay w/ a first gen body around it
so far the only renesis swap ive seen in a first gen actually retained all of the rx-8's fuel injection and engine controls...looked like an rx-8's engine bay w/ a first gen body around it
Trending Topics
#9
Who wants to be pisst' on
Join Date: May 2007
Location: Bpt,Ct
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
i think u should definetly do it. i think that the rennisis fb is frickin cool its my favorite fb besides blown and twisteds fb to fd. if i had a way to get a 13b rennisis and the time and alot of money id do it. imo i think its cooler than a t2 swap just not as good performance wise.
#10
Junior Member
Thread Starter
Join Date: Jun 2007
Location: osgoode/canada
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
thanks keep them comming,,, as per the 13b motor from a rx8 and people have done it.... welll yes mabey ,,, keeping it fuelie sure.. but i would like to switch it to carb..i cant really afford a wrecked rx8 ,, hear in canada its hard , to even get someone that knows anthing about them..I just thiught it would be way kool... and Yes i can get a motor no problem,, and mabey even a long block,, with everthing,, then i may be able to work stuff out,,taking and swapping stuff from the 12a to the 13b,, and permixing the gas is ok,,, i dont mind that at all.. THANKS
#11
wheres the water goin?
iTrader: (9)
Join Date: May 2005
Location: Nor Cal
Posts: 1,586
Likes: 0
Received 0 Likes
on
0 Posts
heres that thread and it was rotarygod not manntis my bad, although manntis has been talk about doing it also.
https://www.rx7club.com/1st-generation-specific-1979-1985-18/rx8-engine-into-1st-gen-rx7-668331/
it sounds pretty easy!
https://www.rx7club.com/1st-generation-specific-1979-1985-18/rx8-engine-into-1st-gen-rx7-668331/
it sounds pretty easy!
Thread
Thread Starter
Forum
Replies
Last Post
KAL797
Test Area 51
0
08-11-15 03:47 PM