What did you do to your FB today?
#7551
Damn, it did start!
Truer words.
Im at a point where I have all the hard to find bits. Massive challenge but worth it. One part I’m glad I did was to get the passenger door hinges from Australia. So my drivers door feels amazing. No sloppy hinges.
I should have the brake system completed in a few weeks. Cooling system should be done, minus an electric fan. And the parts for the turbo header will likely be ordered in a couple of days. My build page should be on fire soon
Im at a point where I have all the hard to find bits. Massive challenge but worth it. One part I’m glad I did was to get the passenger door hinges from Australia. So my drivers door feels amazing. No sloppy hinges.
I should have the brake system completed in a few weeks. Cooling system should be done, minus an electric fan. And the parts for the turbo header will likely be ordered in a couple of days. My build page should be on fire soon
yep- get 'em while you can! Been doing so over the last 20 yrs and it saddens me to see the stuff I used to be able to walk into a dealership and order - and now is NLA!!! I dreamt we might get the aftermarket support for parts the 240Zs enjoy, but it does not look like that will ever happen...
Stu A
80GS
AZ
Stu A
80GS
AZ
The following users liked this post:
LEGALIZECHEY (01-04-21)
#7552
Waffles - hmmm good
iTrader: (1)
Finally painted a set of GS/GSL/SE mirrors to match. The paint match came out perfectly, just not sure they look how I envisioned them. I’ll live with it for a while and can always re-spray. I painted a buddy’s bumpers and decided to do these too. No sense wasting expensive paint.
#7554
Damn, it did start!
Some parts for the turbo manifold and down pipe arrived along with a new radiator!
The following 4 users liked this post by Richard Miller:
#7556
Damn, it did start!
#7557
Rotary Enthusiast
Replaced speakers
I finally upgraded my speakers. The new ones are a definite improvement over the old alpines. The old ones may have worked better after I re-ran all new wire. I’m surprised they worked at all with all the botched wiring Jerry, the PO did.
The second picture is just the left side speaker wiring. Nine splices! If you don’t know what you’re doing, get someone to do it for you, the right way.
Next year, I’ll get a new head unit. Nothing fancy, just a little better than the crappy pioneer.
The second picture is just the left side speaker wiring. Nine splices! If you don’t know what you’re doing, get someone to do it for you, the right way.
Next year, I’ll get a new head unit. Nothing fancy, just a little better than the crappy pioneer.
#7558
Rotary Enthusiast
The following users liked this post:
Toruki (01-12-21)
#7560
Damn, it did start!
Gauge installed. Center console is done.😎🎶🥳
The following users liked this post:
LEGALIZECHEY (01-18-21)
The following 2 users liked this post by Frankenrex:
Richard Miller (01-14-21),
Seniorchief (01-17-21)
#7564
3D Printed
#7565
RX HVN
iTrader: (2)
Easy to see how one could plunder the whole electric system trying to solve this, then squint at the dash: "....waaaaait a minute...!"
d-OH!
What a pain to have to burrow into the whole cluster to fix!!
sympathies!
Stu A
80GS
AZ
#7567
3D Printed
The following users liked this post:
LEGALIZECHEY (02-14-21)
The following users liked this post:
LEGALIZECHEY (02-14-21)
#7570
Damn, it did start!
Energized the Haltech and made the tach do things.
The following 2 users liked this post by Richard Miller:
raven12aFB (03-01-21),
t_g_farrell (03-02-21)
#7571
Senior Member
Just made an order for the parts to finish the front end and ordered also the 3 row aluminum radiator and the e-fan...
Just getting closer to finish her...
Just getting closer to finish her...
The following users liked this post:
Richard Miller (03-01-21)
The following 8 users liked this post by liondogs:
cpt_gloval (10-04-21),
LEGALIZECHEY (03-12-21),
Manny3 (03-12-21),
raven12aFB (03-02-21),
Richard Miller (03-03-21),
and 3 others liked this post.
The following 3 users liked this post by liondogs:
The following users liked this post:
Manny3 (03-12-21)
#7575
Rotary Enthusiast
The following 2 users liked this post by ATC529R:
garagemahal76 (03-12-21),
Manny3 (03-12-21)