the cliche and played out, but never bad looking parking garage photoshoot. (no 56k)
#1
Rotary Freak
Thread Starter
Join Date: Jun 2003
Location: Land Of Confusion southern MI, USA
Posts: 2,604
Likes: 0
Received 1 Like
on
1 Post
the cliche and played out, but never bad looking parking garage photoshoot. (no 56k)
so here are some pictures of my car, version 2.0, now im not done with the paint, keep in mind i will add more coats later. but ive got the aero kit mounted, and ive got my tokicos all the way around, with RB springs up front, and isc racing adjustable spring perches in the rear.
Last edited by perfect_circle; 05-15-08 at 01:09 AM.
Trending Topics
#14
Rotary Freak
Thread Starter
Join Date: Jun 2003
Location: Land Of Confusion southern MI, USA
Posts: 2,604
Likes: 0
Received 1 Like
on
1 Post
the rims are enkies 13", and i do have a spoilerm its a one piece wrap around, but it needs some finishing work, i dont have any idea how to mount it, and im not even sure if i want to....
thanks for all the kind words..... and for the record, the thing is a blast to drive now with the new suspension, like 10x more fun than before.
here is a before shot to show what ive done with it since i bought it in '06
Last edited by perfect_circle; 05-15-08 at 11:48 AM.
#17
Rotary Freak
Thread Starter
Join Date: Jun 2003
Location: Land Of Confusion southern MI, USA
Posts: 2,604
Likes: 0
Received 1 Like
on
1 Post
you as well, are you going to be around for any more events this summer? and if i could give you a piece of advice, a decent set of tires would greatly allow you to take advantage of your suspension mods. like the sumitomos that everyone runs are only like 52$ a tire... but either way, hope to race with you again!
#18
Never Follow
iTrader: (18)
to be completely honest your car was one of the ones that inspired me to paint it this way.
the rims are enkies 13", and i do have a spoilerm its a one piece wrap around, but it needs some finishing work, i dont have any idea how to mount it, and im not even sure if i want to....
thanks for all the kind words..... and for the record, the thing is a blast to drive now with the new suspension, like 10x more fun than before.
the rims are enkies 13", and i do have a spoilerm its a one piece wrap around, but it needs some finishing work, i dont have any idea how to mount it, and im not even sure if i want to....
thanks for all the kind words..... and for the record, the thing is a blast to drive now with the new suspension, like 10x more fun than before.
Yea I have a 1pc spoiler I picked up a year ago that I want to put on mine to replace the "it sort of fits" FC spoiler but haven't gotton around to it either...
I bet its a blast, new suspension always feels great on these cars.
Keep it up, it looks way better than where it started
#20
Rotary Freak
Thread Starter
Join Date: Jun 2003
Location: Land Of Confusion southern MI, USA
Posts: 2,604
Likes: 0
Received 1 Like
on
1 Post
its a bees nest, its been there since my car sat when right after i toasted my clutch and bent my axle in the same day....truth be told, the axle was bent when i bought it, but it got worse at my first autocross
#22
Lives on the Forum
Join Date: Apr 2005
Location: san diego
Posts: 23,563
Likes: 0
Received 0 Likes
on
0 Posts
to the OP what kind of paint did you use. now that i look a bit closer it looks gloss. also what kind ofprep work did you do to the body pieces. it seems from the pic there are a lot of waves in your sides
this is mine
i also took it a step further and candied the corner markers and fog lights
Last edited by 2cute; 05-20-08 at 11:07 AM.
#23
Rotary Freak
Thread Starter
Join Date: Jun 2003
Location: Land Of Confusion southern MI, USA
Posts: 2,604
Likes: 0
Received 1 Like
on
1 Post
i just used rustoleum spray paint, it is supposed to be gloss, buts its on there so thin that there isnt enough to reflect the light. when i get my **** together and have more time ill finish it off. i used an orbital sander with 120 grit paper. i know i need to go alot higher if i want it to look good, but for the time being it will do. i can see swirrels all over from the sanding, like on the hard lines were its hard to get a sander, places that need to be hand sanded. but for less than 12 hours work inclusive, im not complaining
#24
Lives on the Forum
Join Date: Apr 2005
Location: san diego
Posts: 23,563
Likes: 0
Received 0 Likes
on
0 Posts
im just curious why wouldnt you just wait till you had the time and ability to paint it properly?
now those need to be skimmed before proper painting. you just made a lot more work for yourself....
i guess to each their own though...
as for 120 grit.........lol thats what i STARTED with to pull the paint off from the previous owner of the rear and sides...........i ended up with like 800 or 1000 i cant remember for sure........and while i will say this kit is well built and in good shape new there is still stuff wrong with the mold.....so where was a lot of prep work required.....which obviously you neglected......
now those need to be skimmed before proper painting. you just made a lot more work for yourself....
i guess to each their own though...
as for 120 grit.........lol thats what i STARTED with to pull the paint off from the previous owner of the rear and sides...........i ended up with like 800 or 1000 i cant remember for sure........and while i will say this kit is well built and in good shape new there is still stuff wrong with the mold.....so where was a lot of prep work required.....which obviously you neglected......
#25
Rotary Freak
Thread Starter
Join Date: Jun 2003
Location: Land Of Confusion southern MI, USA
Posts: 2,604
Likes: 0
Received 1 Like
on
1 Post
well it looks better here than sitting in my garage. this is no show car, intend to drive it, and i dont want to wince every time i hit a cone at an autocross....
seriously, your rims cost more than my entire car.
seriously, your rims cost more than my entire car.