Anyone ever use RB's Exhaust tubing?
#1
Anyone ever use RB's Exhaust tubing?
http://www.racingbeat.com/resultset....rtNumber=16220
http://www.racingbeat.com/resultset....rtNumber=16122
Anyone ever use these to build an exhaust system? I have had two of their 2.5"
tubes and used it as breaker bars . Now I want to actually use them in my
exhaust system. My current exhaust bangs on my axle on bumps, gets annoying
quite fast. What I will be using is from the RB header, to two Borla's, then over the
axle to the last Borla. Granted, I will only need a little of the straight tubing, how
much of the U bend pipe will I need? I am leaning towards 2 of them?
http://www.racingbeat.com/resultset....rtNumber=16122
Anyone ever use these to build an exhaust system? I have had two of their 2.5"
tubes and used it as breaker bars . Now I want to actually use them in my
exhaust system. My current exhaust bangs on my axle on bumps, gets annoying
quite fast. What I will be using is from the RB header, to two Borla's, then over the
axle to the last Borla. Granted, I will only need a little of the straight tubing, how
much of the U bend pipe will I need? I am leaning towards 2 of them?
#2
Lives on the Forum
I haven't used just their piping, but I have the entire system. Tubing seems to be very heavy gauge, so it should help to avoid the "tinny" sound that thin tubing seems to produce.
3 Borlas?!? Holy **** man! Just wondering why you want the extra Borlas, rather than using their presilencers. I'm sure you have a reason, just want to know what it might be.
I've been thinking about getting rid of my RB muffler and switching over to a Borla this year. I'd like to increase the sound level a tad, and if it flows better then that would be nice too. But my RB system is just too quiet for my tastes.
.
3 Borlas?!? Holy **** man! Just wondering why you want the extra Borlas, rather than using their presilencers. I'm sure you have a reason, just want to know what it might be.
I've been thinking about getting rid of my RB muffler and switching over to a Borla this year. I'd like to increase the sound level a tad, and if it flows better then that would be nice too. But my RB system is just too quiet for my tastes.
.
#3
Waffles - hmmm good
iTrader: (1)
Stu stop!
Read this thread it might give you some ideas.
https://www.rx7club.com/naturally-aspirated-performance-forum-220/informative-exhaust-tuning-what-part-system-actually-tunes-883371/
Read this thread it might give you some ideas.
https://www.rx7club.com/naturally-aspirated-performance-forum-220/informative-exhaust-tuning-what-part-system-actually-tunes-883371/
#4
I haven't used just their piping, but I have the entire system. Tubing seems to be very heavy gauge, so it should help to avoid the "tinny" sound that thin tubing seems to produce.
3 Borlas?!? Holy **** man! Just wondering why you want the extra Borlas, rather than using their presilencers. I'm sure you have a reason, just want to know what it might be.
I've been thinking about getting rid of my RB muffler and switching over to a Borla this year. I'd like to increase the sound level a tad, and if it flows better then that would be nice too. But my RB system is just too quiet for my tastes.
.
3 Borlas?!? Holy **** man! Just wondering why you want the extra Borlas, rather than using their presilencers. I'm sure you have a reason, just want to know what it might be.
I've been thinking about getting rid of my RB muffler and switching over to a Borla this year. I'd like to increase the sound level a tad, and if it flows better then that would be nice too. But my RB system is just too quiet for my tastes.
.
#5
Stu stop!
Read this thread it might give you some ideas.
https://www.rx7club.com/showthread.php?t=883371
Read this thread it might give you some ideas.
https://www.rx7club.com/showthread.php?t=883371
#6
Moderator
iTrader: (3)
Join Date: Mar 2001
Location: https://www2.mazda.com/en/100th/
Posts: 30,792
Received 2,573 Likes
on
1,829 Posts
http://www.racingbeat.com/resultset....rtNumber=16220
http://www.racingbeat.com/resultset....rtNumber=16122
Anyone ever use these to build an exhaust system? I have had two of their 2.5"
tubes and used it as breaker bars . Now I want to actually use them in my
exhaust system. My current exhaust bangs on my axle on bumps, gets annoying
quite fast. What I will be using is from the RB header, to two Borla's, then over the
axle to the last Borla. Granted, I will only need a little of the straight tubing, how
much of the U bend pipe will I need? I am leaning towards 2 of them?
http://www.racingbeat.com/resultset....rtNumber=16122
Anyone ever use these to build an exhaust system? I have had two of their 2.5"
tubes and used it as breaker bars . Now I want to actually use them in my
exhaust system. My current exhaust bangs on my axle on bumps, gets annoying
quite fast. What I will be using is from the RB header, to two Borla's, then over the
axle to the last Borla. Granted, I will only need a little of the straight tubing, how
much of the U bend pipe will I need? I am leaning towards 2 of them?
if i have time i'll snap a pic, the RB pipe is BEEFYx3
i'd think you would want 2 bends.
#7
Lapping = Fapping
iTrader: (13)
Be careful when you order the u-bends. Seems their site has a slight glitch on the 2.5" u-bend page when you click the add to cart button (see the ^25^^"> there?).
If you save this html code to your computer and click the link, it works. I simply edited it slightly. No viruses or trojans. lol
Or if you decide to call to place your order, let them know there is a glitch. Thanks.
If you save this html code to your computer and click the link, it works. I simply edited it slightly. No viruses or trojans. lol
Code:
<html> <head> <title>Racing Beat Results Set</title> <base target="_blank"> </head> <body bgcolor="#FFFFFF" text="#000000" link="#FF0000" vlink="#FF0000"> <div align="center"><center> <table border="0" cellspacing="0" cellpadding="0"> <tr> <td><div align="left"> <table border="0" cellspacing="0" bordercolor="#000000" cellpadding="0"> <tr> <td><img src="photos/16189.jpg" border="0"></td> </tr> </table> </div></td> <td valign="top" align="right"><font face="Arial" size="4"><strong>U-Bend Pipe 2.5" OD<br>4-inch Radius</strong></font><br> <br> <form method="POST" action="https://www.racingbeat.com/cgi-bin/cartit.exe"> <font face="Arial" size="3"><strong>Part Number: 16220</strong></font> <br> <font face="Arial" size="3"><strong>Retail Price: $20.00<br> Qty:</strong></font> <input type="text" size="3" name="Quantity" value="1"><br> <input type="hidden" NAME="cartitadd" VALUE="16220-U-Bend Pipe 2.5 OD<br>4-inch Radius^20^^"> <input type="image" src="images/AddToCart.gif" border="0" WIDTH="80" HEIGHT="27" hspace="0" vspace="1"><br> </p> </form> </td> </tr> <tr> <td><br> </td> <td valign="top" align="right"></td> </tr> <tr> <td colspan="2"><br> <p><font face="Arial" size="2"><b>U-Bend Pipe 2.5" OD - 4" Radius</b><br><br> We offer 2.5-inch OD U-bend tubes with a 4-inch centerline bend radius for use in fabricating a custom exhaust system. The tubing used for this component is 2.5-inch O.D., mandrel bend mild steel with .125-inch wall thickness. </font></td> </tr> </table> </center></div> <p><font face="Arial" size="2"></font></p> </body> </html>
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM