Wolf 3D Idle Set Up
#26
Coyote
Thread Starter
Join Date: Nov 2004
Location: Malta. Europe
Posts: 953
Likes: 0
Received 0 Likes
on
0 Posts
And, as an after though...my BAC is so noisy with ignition on!! what frequency does the stock use? could it be my solenoid is F ed? I mean i never hear a stock Series 6 going bbbbbbbbzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz with ignition on!!!and i tried all freq from 0-255....the freq varies tue....but still loud!!
at round 30 it quites down all together....but then.....no rpm changes at 30!!!!
at round 30 it quites down all together....but then.....no rpm changes at 30!!!!
#27
Coyote
Thread Starter
Join Date: Nov 2004
Location: Malta. Europe
Posts: 953
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by signofinfinity
ok....so with some other issues solved i can go on with the thread.....
i am running better with 16 degrees split....and some -12 overall trim.
so i must start again working on the central temp....
but this is my injector sequence.....
Inj1 offset 0(Rotor1)
Inj2 offset 0(Rotor1)
Inj3 offset 1
Inj4 offset 1
stge offset 0
Inj1 Skip 1(Rotor2)
Inj2 Skip 1(Rotor2)
Inj3 Skip 1
Inj4 Skip 1
Stge Skip 0
now, i figure thats the config.....but i may be wrong with a skip of 5 set on the triggering....
i am running better with 16 degrees split....and some -12 overall trim.
so i must start again working on the central temp....
but this is my injector sequence.....
Inj1 offset 0(Rotor1)
Inj2 offset 0(Rotor1)
Inj3 offset 1
Inj4 offset 1
stge offset 0
Inj1 Skip 1(Rotor2)
Inj2 Skip 1(Rotor2)
Inj3 Skip 1
Inj4 Skip 1
Stge Skip 0
now, i figure thats the config.....but i may be wrong with a skip of 5 set on the triggering....
I ask this coz that would also change the offset timing....and if i am off...my emmisions are high. so that might be a very good start point for countering my emmisions. any test that comes to mind?
#29
Coyote
Thread Starter
Join Date: Nov 2004
Location: Malta. Europe
Posts: 953
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by RotorMotor2
you should have led's on your wolf, change a setting under idle and see if it lights up.
#30
Coyote
Thread Starter
Join Date: Nov 2004
Location: Malta. Europe
Posts: 953
Likes: 0
Received 0 Likes
on
0 Posts
Inj1 offset 0(Rotor1)
Inj2 offset 0(Rotor1)
Inj3 offset 1
Inj4 offset 1
stge offset 0
Inj1 Skip 1(Rotor2)
Inj2 Skip 1(Rotor2)
Inj3 Skip 1
Inj4 Skip 1
Stge Skip 0
...let me get this right.....is my injector sequence making sense???? coz i think it should be more like:
I1=off1
I2=Off1
I3=Off0
I4=Off0
I1,2,3,4 offset=1
Stage Skip1
Inj2 offset 0(Rotor1)
Inj3 offset 1
Inj4 offset 1
stge offset 0
Inj1 Skip 1(Rotor2)
Inj2 Skip 1(Rotor2)
Inj3 Skip 1
Inj4 Skip 1
Stge Skip 0
...let me get this right.....is my injector sequence making sense???? coz i think it should be more like:
I1=off1
I2=Off1
I3=Off0
I4=Off0
I1,2,3,4 offset=1
Stage Skip1
Last edited by signofinfinity; 05-17-05 at 02:06 AM.
#31
Coyote
Thread Starter
Join Date: Nov 2004
Location: Malta. Europe
Posts: 953
Likes: 0
Received 0 Likes
on
0 Posts
ok.....my latest...
02 widewand: .44%
CO2 10.0%....
darn primary injector sockets where inverted!!!!!!
now as i lean over all, i see a significant and relative indication on the stochiometer!!!!
so my plugs where...1 instead of 2 and vice versa....
rough idle but good pickup!!!
will keep ya posted.
02 widewand: .44%
CO2 10.0%....
darn primary injector sockets where inverted!!!!!!
now as i lean over all, i see a significant and relative indication on the stochiometer!!!!
so my plugs where...1 instead of 2 and vice versa....
rough idle but good pickup!!!
will keep ya posted.
Last edited by signofinfinity; 05-17-05 at 09:37 AM.
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
imitek
3rd Generation Specific (1993-2002)
9
08-28-15 05:28 PM
ncds_fc
New Member RX-7 Technical
1
08-15-15 10:06 AM