David Hayes

iTrader: (6)

Hello,

I have a Wolf 3D and Innovate Datalogger available for purchase. You may have followed my thread, FD Pettit 20B Conversion, on this forum:

https://www.rx7club.com/build-threads-292/kilo-racing-3-rotor-fd-conversion-325733/

If you want the long version of the story, read the thread. Some of it's actually interesting The short version is the car is now at Gotham Racing and they have elected to install a Haltech unit due to Steve Kan's familiarity with the system. Thus, my Wolf 3D system is up for sale.

I have the Wolf 3D EMS unit, the software, the manual, and the wiring harness. I also have an Innovate datalogger and the wideband o2 sensor, a must IMO if you are going to run a stand alone EMS.

PM or email me at david.hayes@earthlink.net if you are interested.

David Hayes

iTrader: (6)

Anyone? The unit has about 3 months of actual use on it. Was installed by Chris Green down at Pettit. Drove the car for 3 months and then blew out the secondary turbo. The rest is posted in my thread.

signofinfinity

does it still has the burnt component dave?

what are you asking for the unit price?

David Hayes

iTrader: (6)

PM sent. The unit is in A+ condition.

David Hayes

iTrader: (6)

signofinfinity aksed the above question about my Wolf unit. I now need your help.

While my car was being tuned at Pettit Racing, Cam opened up the unit and found a burnt connector on the circuit board. He called Wolf Australia and sent them pics of the unit. Here is one of the pics (after correction):



Wolf responded by stating the section of the board that was burnt was not used by the Wolf unit (they said they start with a generic motherboard) and the area would not affect the Wolf unit. Can anyone confirm this? As a safeguard, Pettit went ahead and fixed the section anyway. Although the Wolf performed flawlessly in my car for 3 or so months, I don't want to offer/sell a "bad" unit.

As a second issue, Wolf had Pettit solder on the below connector:



Again, it's been so long I can't remember why this was added. I seem to recall it was added because I have a 20B and we used this connector to run the Dakota Digital RPM convertor but I can't remember. Can anyone assist with this? Thanks for the help.

A few extra pics:

signofinfinity

pm sent David

David Hayes

iTrader: (6)

pm sent back to you

David Hayes

iTrader: (6)

In addition to the Wolf EMS pictured in previous posts, below are several pics of other the items included in the sale:

Wolf handheld unit:


Innovate LM1 unit:


Innovate wiring harness and wideband O2 sensor:


Dakota Digital RPM convertor (needed for 20B engine):

David Hayes

iTrader: (6)

Several pictures of the included wiring harness:

[img]https://www.rx7club.com/attachment.php?attachmentid=225885&stc=1[img]

Wolf EMS connectors:


Terminating end of harness:


Connectors in middle of harness:


Pic of the complete harness:

Michael Smith

Thats a V4 ++ ECU even better anyone need a 20B implant???

I do have a push bike that hasn't go a Rotary engine in it hmmmm.

signofinfinity

pm sent again..... sorry for delay.... too much work damn it!

David Hayes

iTrader: (6)

PM send back to you.

signofinfinity

Owned!..... pm u now.

David Hayes

iTrader: (6)

Email sent to you this morning!

David Hayes

iTrader: (6)

Unit sold to Signofinfinity and soon to be on its way to Malta! Check your email George.

signofinfinity

E mail checked! Thanks! Look forward to get it hooked up

Thanks dave...... a pleasure doing business with you!

signofinfinity

Guys.....If David ever want to sell you anything..... BUY IT! Stuff was immaculate! diligently packed in packing and poly!!!!

Thanks David for your help in this! Was a pleasure doing business with you!!!

George

David Hayes

iTrader: (6)

My pleasure George. Thanks for the props