FS: Wolf 3D V4 EMS and Innovate Datalogger
Hello,
I have a Wolf 3D and Innovate Datalogger available for purchase. You may have followed my thread, FD Pettit 20B Conversion, on this forum: https://www.rx7club.com/build-threads-292/kilo-racing-3-rotor-fd-conversion-325733/ If you want the long version of the story, read the thread. Some of it's actually interesting:) The short version is the car is now at Gotham Racing and they have elected to install a Haltech unit due to Steve Kan's familiarity with the system. Thus, my Wolf 3D system is up for sale. I have the Wolf 3D EMS unit, the software, the manual, and the wiring harness. I also have an Innovate datalogger and the wideband o2 sensor, a must IMO if you are going to run a stand alone EMS. PM or email me at david.hayes@earthlink.net if you are interested. |
Anyone? The unit has about 3 months of actual use on it. Was installed by Chris Green down at Pettit. Drove the car for 3 months and then blew out the secondary turbo. The rest is posted in my thread.
|
does it still has the burnt component dave?
what are you asking for the unit price? |
Originally Posted by signofinfinity
does it still has the burnt component dave?
what are you asking for the unit price? PM sent. The unit is in A+ condition. |
5 Attachment(s)
Originally Posted by signofinfinity
does it still has the burnt component dave?
what are you asking for the unit price? While my car was being tuned at Pettit Racing, Cam opened up the unit and found a burnt connector on the circuit board. He called Wolf Australia and sent them pics of the unit. Here is one of the pics (after correction): https://www.rx7club.com/attachment.p...d=225479&stc=1 Wolf responded by stating the section of the board that was burnt was not used by the Wolf unit (they said they start with a generic motherboard) and the area would not affect the Wolf unit. Can anyone confirm this? As a safeguard, Pettit went ahead and fixed the section anyway. Although the Wolf performed flawlessly in my car for 3 or so months, I don't want to offer/sell a "bad" unit. As a second issue, Wolf had Pettit solder on the below connector: https://www.rx7club.com/attachment.p...d=225480&stc=1 Again, it's been so long I can't remember why this was added. I seem to recall it was added because I have a 20B and we used this connector to run the Dakota Digital RPM convertor but I can't remember. Can anyone assist with this? Thanks for the help. A few extra pics: https://www.rx7club.com/attachment.p...d=225481&stc=1 https://www.rx7club.com/attachment.p...d=225482&stc=1 https://www.rx7club.com/attachment.p...d=225483&stc=1 |
pm sent David :)
|
pm sent back to you:)
|
Other pictures
4 Attachment(s)
In addition to the Wolf EMS pictured in previous posts, below are several pics of other the items included in the sale:
Wolf handheld unit: https://www.rx7club.com/attachment.p...d=225881&stc=1 Innovate LM1 unit: https://www.rx7club.com/attachment.p...d=225882&stc=1 Innovate wiring harness and wideband O2 sensor: https://www.rx7club.com/attachment.p...d=225884&stc=1 Dakota Digital RPM convertor (needed for 20B engine): https://www.rx7club.com/attachment.p...d=225883&stc=1 |
Wolf EMS wiring harness
4 Attachment(s)
Several pictures of the included wiring harness:
[img]https://www.rx7club.com/attachment.php?attachmentid=225885&stc=1[img] Wolf EMS connectors: https://www.rx7club.com/attachment.p...d=225886&stc=1 Terminating end of harness: https://www.rx7club.com/attachment.p...d=225887&stc=1 Connectors in middle of harness: https://www.rx7club.com/attachment.p...d=225888&stc=1 Pic of the complete harness: https://www.rx7club.com/attachment.p...d=225885&stc=1 |
Thats a V4 ++ ECU even better anyone need a 20B implant???http://www.drunkendonkey.net/eng/html/emoticons/sun.gifhttp://4fxearth.net/phpBB2/smilies_m...9c7284ce9f.gif
I do have a push bike that hasn't go a Rotary engine in it hmmmm. |
pm sent again..... sorry for delay.... too much work damn it!
|
Originally Posted by signofinfinity
pm sent again..... sorry for delay.... too much work damn it!
PM send back to you. |
Owned!..... pm u now.
|
Email sent to you this morning!
|
Unit sold to Signofinfinity and soon to be on its way to Malta! Check your email George.
|
E mail checked! Thanks! Look forward to get it hooked up :D
Thanks dave...... a pleasure doing business with you! |
Guys.....If David ever want to sell you anything..... BUY IT! Stuff was immaculate! diligently packed in packing and poly!!!!
Thanks David for your help in this! Was a pleasure doing business with you!!! George |
My pleasure George. Thanks for the props:)
|
All times are GMT -5. The time now is 04:38 AM. |
© 2024 MH Sub I, LLC dba Internet Brands