HID Conversion Kit Special $60.00 Shipped for rx7club.com members
#153
Hi,
your bulb type is below
1993 MAZDA RX-7
High & low beam headlamp
9003=H4
You have two choices for the H4/9003 (H4=9003) (hi/lo and bi-xenon)
hi/lo means your low beam is HID and high beam is Halogen because this bulb type has two bulbs in one bulb base to go from low to high beam.
And the bi-xenon means both your low and high beams will be HID.
Here is the link to your H4/9003 hi/lo 6000K ($60 after coupon code: fspecial-m)
http://www.hidextra.com/HID+Conversi...rsion+Kit.html
Here is the link to your H4/9003 bi-xenon 6000K ($90 after coupon code:fspecial-m)
http://www.hidextra.com/HID+Conversion+Kits/Automobile+HID+Kits/H4+Bi-Xenon+HID+Kit/H4+Bi-Xenon+6000K/H4+Bi-Xenon-6000K+Automobile+Xenon+HID+Conversion+Kit.html
You will not need anything extra the kit comes with everything you need (2 bulbs, 2 ballast, 2 wire harness(or relay + wire harness for bi-xenon) and 2 adhesive pads and some zip ties.
let meknow if you need anything else.
Thanks~
Michelle
your bulb type is below
1993 MAZDA RX-7
High & low beam headlamp
9003=H4
You have two choices for the H4/9003 (H4=9003) (hi/lo and bi-xenon)
hi/lo means your low beam is HID and high beam is Halogen because this bulb type has two bulbs in one bulb base to go from low to high beam.
And the bi-xenon means both your low and high beams will be HID.
Here is the link to your H4/9003 hi/lo 6000K ($60 after coupon code: fspecial-m)
http://www.hidextra.com/HID+Conversi...rsion+Kit.html
Here is the link to your H4/9003 bi-xenon 6000K ($90 after coupon code:fspecial-m)
http://www.hidextra.com/HID+Conversion+Kits/Automobile+HID+Kits/H4+Bi-Xenon+HID+Kit/H4+Bi-Xenon+6000K/H4+Bi-Xenon-6000K+Automobile+Xenon+HID+Conversion+Kit.html
You will not need anything extra the kit comes with everything you need (2 bulbs, 2 ballast, 2 wire harness(or relay + wire harness for bi-xenon) and 2 adhesive pads and some zip ties.
let meknow if you need anything else.
Thanks~
Michelle
I have the same car 93 FD - i'm looking at the 6000K Bi-Xenon.
it says with relay + wire harness,
Is this a plug and play kit?
#154
Site Sponsor
Thread Starter
iTrader: (3)
Join Date: Jun 2009
Location: Freemont
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
Hi,
Yes! It's all plug and play the bi-xenon will come with it's own relay and you will get your instructions in the kit too.
Let meknow when you order so I can see if you order went through. Thanks!
Michelle
Yes! It's all plug and play the bi-xenon will come with it's own relay and you will get your instructions in the kit too.
Let meknow when you order so I can see if you order went through. Thanks!
Michelle
#156
Senior Member
iTrader: (10)
Join Date: Apr 2006
Location: houston, tx
Posts: 536
Likes: 0
Received 0 Likes
on
0 Posts
hey Michelle thanks for the kits. i received both of them yesterday and according to the pics everything looks to be in order.
thanks again, mark
p.s. i'll be installing them in a few weeks when i get home, i'll let you know how it goes.
thanks again, mark
p.s. i'll be installing them in a few weeks when i get home, i'll let you know how it goes.
#160
Site Sponsor
Thread Starter
iTrader: (3)
Join Date: Jun 2009
Location: Freemont
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email.
I will be overseas for the month of September but will still respond to all online inquiries. If you need immediate assistance or technical support, please call 860-821-8212 between 10am-4pm PST (Mon-Fri). Thank you very much!
I will be overseas for the month of September but will still respond to all online inquiries. If you need immediate assistance or technical support, please call 860-821-8212 between 10am-4pm PST (Mon-Fri). Thank you very much!
#161
Site Sponsor
Thread Starter
iTrader: (3)
Join Date: Jun 2009
Location: Freemont
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email.
I will be overseas for the month of September but will still respond to all online inquiries. If you need immediate assistance or technical support, please call 860-821-8212 between 10am-4pm PST (Mon-Fri). Thank you very much!
I will be overseas for the month of September but will still respond to all online inquiries. If you need immediate assistance or technical support, please call 860-821-8212 between 10am-4pm PST (Mon-Fri). Thank you very much!
#165
Full Member
iTrader: (2)
What about the other stock connector?
I bought the Bi-Xenon kit and there is only 1 connector to plug into the stock 3-prong harness. My other stock harness has nothing to plug into it. Should it just hang there not connected to anything? Is my kit missing something?
I installed everything and the headlights do not work. Can anyone offer advice before the weekend is over?!
I installed everything and the headlights do not work. Can anyone offer advice before the weekend is over?!
#166
Rotary Enthusiast
iTrader: (16)
wolfman,
What did you connect your (red) power wire to? And plug in the 3 prong plug to the connector if you haven't already.
Also, my battery is behind my passanger seat so I plugged it up to my alternator for power. My drivers side light keeps going out after a few minutes and will only come back on if I turn of all the lights then turn them all back on, but it still goes out after the same amount of time??
Other HID stays on... maybe i need to extend the wire to reach my battery?... any help with this problem would be great, thanks!
What did you connect your (red) power wire to? And plug in the 3 prong plug to the connector if you haven't already.
Also, my battery is behind my passanger seat so I plugged it up to my alternator for power. My drivers side light keeps going out after a few minutes and will only come back on if I turn of all the lights then turn them all back on, but it still goes out after the same amount of time??
Other HID stays on... maybe i need to extend the wire to reach my battery?... any help with this problem would be great, thanks!
#167
Full Member
iTrader: (2)
I connected my red power wire to battery. The drivers side 3 prong plug is connected to the only 3 prong connector in the HID kit. There is no additional 3 prong plug in the kit to connect the one on my passenger side into.
wolfman,
What did you connect your (red) power wire to? And plug in the 3 prong plug to the connector if you haven't already.
Also, my battery is behind my passanger seat so I plugged it up to my alternator for power. My drivers side light keeps going out after a few minutes and will only come back on if I turn of all the lights then turn them all back on, but it still goes out after the same amount of time??
Other HID stays on... maybe i need to extend the wire to reach my battery?... any help with this problem would be great, thanks!
What did you connect your (red) power wire to? And plug in the 3 prong plug to the connector if you haven't already.
Also, my battery is behind my passanger seat so I plugged it up to my alternator for power. My drivers side light keeps going out after a few minutes and will only come back on if I turn of all the lights then turn them all back on, but it still goes out after the same amount of time??
Other HID stays on... maybe i need to extend the wire to reach my battery?... any help with this problem would be great, thanks!
#168
Site Sponsor
Thread Starter
iTrader: (3)
Join Date: Jun 2009
Location: Freemont
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
Hi
Yes the other OEM connector should be left alone since for a bi-xenon kit, you are powering the kit directly from the battery.
You may need to reverse the diode or take off the 4 inch connector on the relay.
Please see the following pertaning to your bulb type
http://www.hid-light.com/install/install.html
THanks!
Michelle
Yes the other OEM connector should be left alone since for a bi-xenon kit, you are powering the kit directly from the battery.
You may need to reverse the diode or take off the 4 inch connector on the relay.
Please see the following pertaning to your bulb type
http://www.hid-light.com/install/install.html
THanks!
Michelle
I bought the Bi-Xenon kit and there is only 1 connector to plug into the stock 3-prong harness. My other stock harness has nothing to plug into it. Should it just hang there not connected to anything? Is my kit missing something?
I installed everything and the headlights do not work. Can anyone offer advice before the weekend is over?!
I installed everything and the headlights do not work. Can anyone offer advice before the weekend is over?!
#169
Site Sponsor
Thread Starter
iTrader: (3)
Join Date: Jun 2009
Location: Freemont
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
All orders placed today before 3pm PST have been shipped. Thanks!
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email.
I will be overseas for the month of September but will still respond to all online inquiries. If you need immediate assistance or technical support, please call 860-821-8212 between 10am-4pm PST (Mon-Fri). Thank you very much!
MIchelle
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email.
I will be overseas for the month of September but will still respond to all online inquiries. If you need immediate assistance or technical support, please call 860-821-8212 between 10am-4pm PST (Mon-Fri). Thank you very much!
MIchelle
#170
Site Sponsor
Thread Starter
iTrader: (3)
Join Date: Jun 2009
Location: Freemont
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
All orders placed before 3pm PST have been shipped.
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email.
I will be overseas for the month of September but will still respond to all online inquiries. If you need immediate assistance or technical support, please call 860-821-8212 between 10am-4pm PST (Mon-Fri). Thank you very much!
Michelle
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email.
I will be overseas for the month of September but will still respond to all online inquiries. If you need immediate assistance or technical support, please call 860-821-8212 between 10am-4pm PST (Mon-Fri). Thank you very much!
Michelle
#171
do you have anymore pics of the 5k and 4ks im ordering a set tomorrow jsut cant make up my mind on what color temp. lol and also could you send me a link for the h4 conversion. thanks alot.
#172
Site Sponsor
Thread Starter
iTrader: (3)
Join Date: Jun 2009
Location: Freemont
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
Hi,
we only have 5000K, 4300K is only for stock HIDs.
Here it he link to the H4 5000K
You have two choices for the H4/9003 (H4=9003) (hi/lo and bi-xenon)
hi/lo means your low beam is HID and high beam is Halogen because this bulb type has two bulbs in one bulb base to go from low to high beam.
And the bi-xenon means both your low and high beams will be HID.
Here is the link to your H4/9003 hi/lo 5000K ($60 after coupon code from first page of the thread or on the signature)
http://www.hidextra.com/HID+Conversi...rsion+Kit.html
Here is the link to your H4/9003 bi-xenon 5000K ($90 after coupon code from first page of the thread or on the signature)
http://www.hidextra.com/HID+Conversi...rsion+Kit.html
THanks!
Michelle
we only have 5000K, 4300K is only for stock HIDs.
Here it he link to the H4 5000K
You have two choices for the H4/9003 (H4=9003) (hi/lo and bi-xenon)
hi/lo means your low beam is HID and high beam is Halogen because this bulb type has two bulbs in one bulb base to go from low to high beam.
And the bi-xenon means both your low and high beams will be HID.
Here is the link to your H4/9003 hi/lo 5000K ($60 after coupon code from first page of the thread or on the signature)
http://www.hidextra.com/HID+Conversi...rsion+Kit.html
Here is the link to your H4/9003 bi-xenon 5000K ($90 after coupon code from first page of the thread or on the signature)
http://www.hidextra.com/HID+Conversi...rsion+Kit.html
THanks!
Michelle
#173
Site Sponsor
Thread Starter
iTrader: (3)
Join Date: Jun 2009
Location: Freemont
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
All orders placed before 3pm PST yesterday have been shipped.
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email. Thank you very much!
Michelle
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email. Thank you very much!
Michelle
#175
Site Sponsor
Thread Starter
iTrader: (3)
Join Date: Jun 2009
Location: Freemont
Posts: 306
Likes: 0
Received 0 Likes
on
0 Posts
All orders placed before 3pm PST yesterday have been shipped. Thank you!
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email. Thank you very much!
Michelle
Due to increasing number of HID inquiries, please allow me 24-48 hrs to respond to your PM, thread replies or Email. Thank you very much!
Michelle