Where to hook up Profec on single turbo?
Where to hook up Profec on single turbo?
I know that the OUT goes to the waste gate. Does the IN go to any source of boost/vac or should I put a little fitting on the intercooler pipe coming right of the turbo for a reading there, that is if thats where the IN should be. Any help would get great.
Thanks Guys
Thanks Guys
On a long vacation
Joined: Feb 2001
Posts: 2,160
Likes: 0
From: Bay Area, CA, U.S.A.
2 of the hoses go to the intake manifold. One goes to the boost controller. I'm pretty sure that's what the manual says. I don't have it right now because I lent it to my friend.
oh lord
the out goes to the wastegate
the in goes to a non vacuum boost source, like a fitting right into the outlet of your turbo.. most people split air from there to the stepper motor in, and to the non vacuum boost source of your wastegate since its close. the hose that goes to the profec-b itself you can run from your upper intake manifold through the firewall
the out goes to the wastegate
the in goes to a non vacuum boost source, like a fitting right into the outlet of your turbo.. most people split air from there to the stepper motor in, and to the non vacuum boost source of your wastegate since its close. the hose that goes to the profec-b itself you can run from your upper intake manifold through the firewall
On a long vacation
Joined: Feb 2001
Posts: 2,160
Likes: 0
From: Bay Area, CA, U.S.A.
Originally posted by Poweraxel
Turbo outlet pressure --> side port of wastegate and the "IN" port
"Out" port--> Top port on wastegate
Turbo outlet pressure --> side port of wastegate and the "IN" port
"Out" port--> Top port on wastegate
I just installed the XS T04E turbo kit this weeked. It came with an HKS wastegate. I have a Blitz DSBC. I hooked up the "out" hose to the wastegate. I hooked up the "in" hose to the intake manifold (plenum). Is that right??? I can't keep my boost under 1 bar. What am I doing wrong? I adjust the switch on the Blitz DSBC to external wastegate. Help...Mad Power, but too maddening
Trending Topics
'Tuna'
Joined: Feb 2001
Posts: 4,637
Likes: 3
From: Miami,Fl,USA
Let's see!
On the Profec---->
OUT---- Goes to the top of the wastegate.
IN------ T's with the hose that's connected to the side of the
wastegate that normally goes to the nipple on the
front of the turbo.
The last hose goes to the back of the control unit and that should be connected to a vacum/pressure source on the intake manifold just the same as the BOV or FPR would be connected too.
crispeed
87TII
9.20@150mph
On the Profec---->
OUT---- Goes to the top of the wastegate.
IN------ T's with the hose that's connected to the side of the
wastegate that normally goes to the nipple on the
front of the turbo.
The last hose goes to the back of the control unit and that should be connected to a vacum/pressure source on the intake manifold just the same as the BOV or FPR would be connected too.
crispeed
87TII
9.20@150mph
The BLITZ DSBC, The BLITZ DSBC....It just has an "IN" and an "OUT". I think I will need to check my HKS wastegate again. I didn't know that you connect anything to the top of the wastegate? I just connnected the "OUT" to the side of the wastegate. Is that wrong. Gotta control the boost....
Thread
Thread Starter
Forum
Replies
Last Post
stickmantijuana
3rd Generation Specific (1993-2002)
5
Jan 11, 2016 04:08 PM
stickmantijuana
Single Turbo RX-7's
0
Aug 21, 2015 08:35 PM
