spool rate of the SR stage 2 turbo...
01-07-03, 04:46 PM
#1
Full Member
Thread Starter
Join Date: Oct 2002
Location: Charleston WV
Posts: 50
Likes: 0
Received 0 Likes
on
0 Posts
spool rate of the SR stage 2 turbo...
What is the spool rate like for the SR stage 2 turbo compared to other turbo setups? How streetable is it? Maybe even Ernie can chime in?
01-07-03, 04:54 PM
#2
I can't help you out too much (no numbers) but I do know the stage 3 is similar to a T78 in terms of power output and size, but spools up a little bit faster.
Therefore, the stage 2 turbo should be even quicker spooling.
Therefore, the stage 2 turbo should be even quicker spooling.
01-07-03, 07:04 PM
#5
Living life 9 seconds at a time
iTrader: (2)
Join Date: Feb 2001
Location: Abingdon, Md
Posts: 6,541
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Bridgeported
I can't help you out too much (no numbers) but I do know the stage 3 is similar to a T78 in terms of power output and size, but spools up a little bit faster.
Therefore, the stage 2 turbo should be even quicker spooling.
I can't help you out too much (no numbers) but I do know the stage 3 is similar to a T78 in terms of power output and size, but spools up a little bit faster.
Therefore, the stage 2 turbo should be even quicker spooling.
I made 372rwhp @ 10psi.... I can't tell ya what I made at 20psi on a stock motor....I'd have to kill ya...
It spools faster than average. I hit 15psi at about 3900-4000 with a 1bar wastegate spring. This summer I'll run 28lbs and see how she does on a ported motor.
01-07-03, 08:26 PM
#6
Senior Member
Join Date: Oct 2001
Location: redmond wa
Posts: 275
Likes: 0
Received 0 Likes
on
0 Posts
That is the K28 turbo right? Wasn't there something going around about how SR was using holset housings and KKK compressors/turbines? Is there any other source for KKK turbos? Lately I've been realizing more and more just how many largely unknown (at least to me) options there are for RX-7 owners that are looking in the 450-550 rwhp range w/ relatively quick response. Sorry sometimes I ramble.
01-07-03, 08:43 PM
#7
Living life 9 seconds at a time
iTrader: (2)
Join Date: Feb 2001
Location: Abingdon, Md
Posts: 6,541
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by milkman2k52
That is the K28 turbo right? Wasn't there something going around about how SR was using holset housings and KKK compressors/turbines?
That is the K28 turbo right? Wasn't there something going around about how SR was using holset housings and KKK compressors/turbines?
Trending Topics
01-23-03, 01:13 AM
#9
Full Member
Join Date: Jan 2003
Location: tracy california
Posts: 221
Likes: 0
Received 0 Likes
on
0 Posts
hmmm as far as comparability, its quite large as i remember, but i know if u check out the sr site, they mad around 550 whp at 19 psi, but its water injected for all u that think its a horrible thing to do to ur 7, newayz check it out, its got a dyno for it, and a list of mods, sounds like a good turbo to me. its bigger than mine so 
01-23-03, 10:09 PM
#10
Rotary Enthusiast
Join Date: Feb 2001
Location: In the Sky
Posts: 1,190
Likes: 0
Received 0 Likes
on
0 Posts
Re: spool rate of the SR stage 2 turbo...
your best bet is to contact www.srx7.com directly
Originally posted by WVSRMOTORSPORTSRX7
What is the spool rate like for the SR stage 2 turbo compared to other turbo setups? How streetable is it? Maybe even Ernie can chime in?
What is the spool rate like for the SR stage 2 turbo compared to other turbo setups? How streetable is it? Maybe even Ernie can chime in?
Thread
Thread Starter
Forum
Replies
Last Post
LongDuck
1st Generation Specific (1979-1985)
12
10-07-15 08:12 PM
eplusz
General Rotary Tech Support
15
10-07-15 04:04 PM
