Single Turbo with PFC Tuning Document Here
05-26-13, 12:39 PM
#126
Blowing smoke...
I put it on Google Docs https://docs.google.com/open?id=0B_j...GZhZEhsM0ZNRk0
The following users liked this post:
norberts94fd (09-11-20)
05-13-14, 09:32 PM
#130
Weird Cat Man
Thread Starter
Just checking in
Just checking in to say hello! Glad to see the doc is up on google docs. Only flaw I saw there is google docs sort of messed up some of the colors in the PDF so you end up with grays where you should have brighter colors. Not a huge deal really, but it can make a few of the graphs harder to understand when I'm talking about something being magenta and all you see is light gray, medium gray, etc.
I realized the email I had associated with this forum account was ANCIENT, so I wasn't getting any PM notifications and since I rarely actually log in, I didn't see the little thing at the top right either saying I had a message.
I updated my email in the rx7club system and enabled email notification of PMs, so if you want the pdf all you should need to do is PM me and it will email a good email that I actually check
I always encourage you to compare my old doc to newer work by other folks on here. A lot has changed over the years and while I do think most of my advice is still pretty good I am sure there are some gaps too. The more you read the better. Mistakes cost time and money so it's better to read more and think first - then go wrenching!
I still have my RX-7 and I am actually thinking about turning it into my daily driver rather than a garage queen. When I'm replacing tires that have almost full tread but are cracking from AGE - that's a wake up call hahaha. Need to drive it more!
I realized the email I had associated with this forum account was ANCIENT, so I wasn't getting any PM notifications and since I rarely actually log in, I didn't see the little thing at the top right either saying I had a message.
I updated my email in the rx7club system and enabled email notification of PMs, so if you want the pdf all you should need to do is PM me and it will email a good email that I actually check
I always encourage you to compare my old doc to newer work by other folks on here. A lot has changed over the years and while I do think most of my advice is still pretty good I am sure there are some gaps too. The more you read the better. Mistakes cost time and money so it's better to read more and think first - then go wrenching!
I still have my RX-7 and I am actually thinking about turning it into my daily driver rather than a garage queen. When I'm replacing tires that have almost full tread but are cracking from AGE - that's a wake up call hahaha. Need to drive it more!
12-18-15, 04:34 PM
#133
:bump: can i get this data ten years after its been discussed?!
the link leads nowhere
Edit: nevermind... found it!
https://drive.google.com/file/d/0B_j...hsM0ZNRk0/view
the link leads nowhere
Edit: nevermind... found it!
https://drive.google.com/file/d/0B_j...hsM0ZNRk0/view
08-22-16, 09:28 PM
#135
Junior Member
Join Date: Aug 2013
Location: Phoenix
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Good stuff in here. Just finished rebuilding a 94 for a friend and now tuning his new single setup with a PowerFC and Datalogit. Hopefully it's not much harder than all the Nissan tuning I'm used to
08-24-17, 12:21 AM
#137
Junior Member
Join Date: Jul 2012
Location: Athens, Greece
Posts: 40
Likes: 0
Received 0 Likes
on
0 Posts
A quick note to anyone with a 2nd gen using either the AP Engineering or Banzai Racing setups:
I have put together a supplementary document explaining some of the small installation and tuning differences when using the PFC on an FC. I also have a handy appendix with pinouts and configuration procedures for your TPS.
http://www.geocities.com/arghx/PowerFC.FC3S.Tuning.doc
I have put together a supplementary document explaining some of the small installation and tuning differences when using the PFC on an FC. I also have a handy appendix with pinouts and configuration procedures for your TPS.
http://www.geocities.com/arghx/PowerFC.FC3S.Tuning.doc
Thread
Thread Starter
Forum
Replies
Last Post
Rotary93
Power FC Forum
2
02-04-02 09:23 AM
