Need Map For New Set-Up
#1
Senior Member
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: Lancaster, PA
Posts: 509
Likes: 0
Received 0 Likes
on
0 Posts
Need Map For New Set-Up
Hi everyone, i was just wondering if anyone might have the same set-up as mine and might be able to share their tuning set-up with me, here are my set-up.
Large Street Port (breaking in)
Tubornetic 60-1 with 81 on hotside i think
OBX 40mm wastegate
550cc and 1300cc
Apexi Power FC with Commander
Front Mount
3 1/2" to 3" all the way back exhault
ACT clutch and flywheel
Warm up Accelerator Removed
Walboro Fuel Pump
Fuel Pressure Regulator
So this is my set-up so if anyone might have the same or similar and don't mind sharing i would appreciate it very much thanks
Large Street Port (breaking in)
Tubornetic 60-1 with 81 on hotside i think
OBX 40mm wastegate
550cc and 1300cc
Apexi Power FC with Commander
Front Mount
3 1/2" to 3" all the way back exhault
ACT clutch and flywheel
Warm up Accelerator Removed
Walboro Fuel Pump
Fuel Pressure Regulator
So this is my set-up so if anyone might have the same or similar and don't mind sharing i would appreciate it very much thanks
#2
Senior Member
iTrader: (3)
Join Date: Sep 2004
Location: Oklahoma City
Posts: 700
Likes: 0
Received 0 Likes
on
0 Posts
I have a map for a FD w/ a larger turbo and secondaries. It would get you started, but if you don't know what you are doing and boost it you will be buying a new motor. I highly recommend paying for it to be done unless you have experienced this in the past. To make a map from scratch takes a lot of time. I have done several from scratch on a PFC and a Haltech. Borrowing a map and trying to drive your car is risky unless you have a wideband and EGT monitors.
#3
Senior Member
Thread Starter
iTrader: (4)
Join Date: Aug 2005
Location: Lancaster, PA
Posts: 509
Likes: 0
Received 0 Likes
on
0 Posts
Hey RotaryInspired how hard is it to just put in a basic map so that i can run and break in the engine, i know i won't want to do it myself but in the future after the break in i will bring it to KDR here where i am to have Dave tune it. But for now i just need something so that i can start the car with out it flooding and drive it to break it in. As of right now with out a map it's basically sending a whole lot of fuel and flood out the engine everytime if i don't rev it up to burn out of the fuel
#5
Out of the game
iTrader: (1)
Join Date: Dec 2004
Location: Reno NV
Posts: 637
Likes: 0
Received 0 Likes
on
0 Posts
Did you put the 1300' secondary's in without adjusting the ECU for it?
You can make these changes with the commander for the 1300cc injectors. search around in the PFC forum or download the Manual if needed.
You can make these changes with the commander for the 1300cc injectors. search around in the PFC forum or download the Manual if needed.
#6
Stud Service
iTrader: (3)
Join Date: Apr 2002
Location: Lancaster PA
Posts: 741
Likes: 0
Received 0 Likes
on
0 Posts
Another FD in little ol' Lancaster...alrighttt. I've got a PFC I purchased used from here. It has a single turbo map on it, but I'm still not finished installing my harness so that I can get the map from it(PFC). Maybe you can search my post and get info from the thread about the set-up. I should have the harness installed by the end of the week.
Thread
Thread Starter
Forum
Replies
Last Post
killerrx710
Adaptronic Engine Mgmt - AUS
5
09-28-15 09:13 AM
killerrx710
2nd Generation Specific (1986-1992)
1
09-24-15 10:57 PM