Originally Posted by Marcel Burkett
(Post 7909888)
Did Ray tell you that thet turbo will support your goal of 700-750 ?
|
Cars now at PFS to get the tune. Turns out I had a bad leading coil that was causing the boost spike, so we'll see sometime this week with numbers
|
intercooler
1 Attachment(s)
i have that intercooler. i think mine says xso2 or o2xs. or something like that. but its like the exact same thing. not sure about the outside dimensions, but it is 4 inches thick. i bought it new from someone on the forum for 200.
|
Nice build man. Let us know how it turns out.
Dee E. |
Thanks man
|
Nice!
|
very nice man cant wait to see some numbers. how much does he charge for dyno time?
|
Labor rate: $85.00/hr
Dyno tuning: $150.00/hr |
Now I have a low compression motor at almost 1k miles, Rays gotta pull it out again. 12k lost =(. another 12k motor with either a 42R on 45R now
|
wow, that sucks. Who did the last build? Did you have nay issues before?
|
Ray at PFS did. IT was my fault, i didn't put enough premix oil in the gas when i filled it up.
|
what? what?
1st of all with 1 thousand miles on the motor there is very VERY little that needs to be replaced. Almost everything should be within spec to be reused. The only thing that I would recommed replacing are the part/ seal that failed..plus new springs and a gasketset It could be a sideseal/cornerseal/apex seal that got stuck.. I doubt it could be a collapsed spring.... 1) gasket set----use a FC N/A gasket set $150 2)buy all new springs (side seal, corner seal, apex seal springs 3)if it is a stuck seal then , you can file the rotor back to within spec if its dented, replace rotor 4) Don't know what apex seal you used but some apes seal tend to break the tips off while other crack in the middle but magically stay in the groove.. replace apex seal 5)close motor and go= wayyyyyyyyyyyyyyyy less then 12K |
Originally Posted by mazgtr
(Post 8006296)
what? what?
1st of all with 1 thousand miles on the motor there is very VERY little that needs to be replaced. Almost everything should be within spec to be reused. The only thing that I would recommed replacing are the part/ seal that failed..plus new springs and a gasketset It could be a sideseal/cornerseal/apex seal that got stuck.. I doubt it could be a collapsed spring.... 1) gasket set----use a FC N/A gasket set $150 2)buy all new springs (side seal, corner seal, apex seal springs 3)if it is a stuck seal then , you can file the rotor back to within spec if its dented, replace rotor 4) Don't know what apex seal you used but some apes seal tend to break the tips off while other crack in the middle but magically stay in the groove.. replace apex seal 5)close motor and go= wayyyyyyyyyyyyyyyy less then 12K |
Originally Posted by rotorsownu
(Post 8006301)
Yeah, but i'm going a diff route...it's a complete bridgeported race everything motor. Onlt thing changing in my motor is ray putting race seals in it instead of 2mm. I'm goin custom 4inch exhaust, custom either 42R, or 45R, gonna need to run 6 injectors shooting for 800+ new ECU, built tranny and a few other things.
|
Lol who's that? time to smoke bikes on a daily bases. And I'm to addicted to this car to sell it, so I guess all I can do is eat my loss.
|
Originally Posted by Marcel Burkett
(Post 8007212)
Your new build sounds a lot like the one being finished up by someone I know pretty well !!
|
lol, wasn't jocking anybodys goals. happen to have some what the same goal I guess. this was my plan a while back, but wanted to get used to 600 first, I didn't even have that chance just jumping straight from 500 to 850 depending on what turbo I choose,
|
Originally Posted by rotorsownu
(Post 8007875)
lol, wasn't jocking anybodys goals. happen to have some what the same goal I guess. this was my plan a while back, but wanted to get used to 600 first, I didn't even have that chance just jumping straight from 500 to 850 depending on what turbo I choose,
|
Nice to see a blown motor doesn't get you down :bigthumb:
|
haha I know right. I just looked at is as if "Damn I had to go back in the motor sooner or later again to make it stronger, better now than later to handle my new goals."
|
Sounds awesome cant wait to see some #'s. When will the new one be built?
|
Originally Posted by siguy2k
(Post 8011567)
Sounds awesome cant wait to see some #'s. When will the new one be built?
|
Well, change of plans, I ran into a bad car situation. I sold both of my cars, now only car I have now is the FD until I buy a new car, so i'm not going with the eshaft, so I should have car back in 3 weeks max. Still should be hitting somewhere in 700's.
|
Nice!!!
|
Thanks, I changed my mind with the 42R, I'm going with a borg warner turbo thats a bit bigger than the 42R
|
All times are GMT -5. The time now is 12:06 PM. |
© 2024 MH Sub I, LLC dba Internet Brands