My BW S475 project... lots of pics.
#277
BTW you need to set your ecu up so it logs on it's own. You don't need to keep your laptop in the car. You can set an external trigger to activate it or simply use rpm to activate it, so anytime your over 1500rpm for example it automatically datalogs. You can then pull data from ecu after the run..
#280
E85 Addict
Thread Starter
Sorry to hear the news.. At least it doesn't look so bad and you should get it up and running quite quickly...
BTW you need to set your ecu up so it logs on it's own. You don't need to keep your laptop in the car. You can set an external trigger to activate it or simply use rpm to activate it, so anytime your over 1500rpm for example it automatically datalogs. You can then pull data from ecu after the run..
BTW you need to set your ecu up so it logs on it's own. You don't need to keep your laptop in the car. You can set an external trigger to activate it or simply use rpm to activate it, so anytime your over 1500rpm for example it automatically datalogs. You can then pull data from ecu after the run..
#282
E85 Addict
Thread Starter
#285
E85 Addict
Thread Starter
#286
E85 Addict
Thread Starter
I see. thats nice. i hope you have a great time and that the weather stays decent!
#288
E85 Addict
Thread Starter
here's a lil' vid from last time at the track
you can comment on my driving all you want, i already know i SUCK!!
either i bog.. or spin so i fall off boost in second.. you can also see the motor let go while on the limiter on the last run
http://www.youtube.com/watch?v=q8jiysn9C4U
my trap speed on 1/8 is 110mph but 1/4 trap is only 134mph.. isn't that a little low?
My tire pressure was way to low, can it be the reason?
you can comment on my driving all you want, i already know i SUCK!!
either i bog.. or spin so i fall off boost in second.. you can also see the motor let go while on the limiter on the last run
http://www.youtube.com/watch?v=q8jiysn9C4U
my trap speed on 1/8 is 110mph but 1/4 trap is only 134mph.. isn't that a little low?
My tire pressure was way to low, can it be the reason?
#291
E85 Addict
Thread Starter
#294
Rotary Freak
Join Date: Nov 2001
Location: trinidad and tobago
Posts: 2,715
Likes: 0
Received 0 Likes
on
0 Posts
here's a lil' vid from last time at the track
you can comment on my driving all you want, i already know i SUCK!!
either i bog.. or spin so i fall off boost in second.. you can also see the motor let go while on the limiter on the last run
http://www.youtube.com/watch?v=q8jiysn9C4U
my trap speed on 1/8 is 110mph but 1/4 trap is only 134mph.. isn't that a little low?
My tire pressure was way to low, can it be the reason?
you can comment on my driving all you want, i already know i SUCK!!
either i bog.. or spin so i fall off boost in second.. you can also see the motor let go while on the limiter on the last run
http://www.youtube.com/watch?v=q8jiysn9C4U
my trap speed on 1/8 is 110mph but 1/4 trap is only 134mph.. isn't that a little low?
My tire pressure was way to low, can it be the reason?
You seem to be failing every time you get up in revs (and hold it there for a while) ! I would guess that you are getting serious crankshaft flex , allowing the rotor to contact the housing , which is causing the seal groove to close in an "clip" the seal! You need to race clearance the rotors and/or invest in a two piece e shaft !
#296
E85 Addict
Thread Starter
when i got a decent burnout it would bog at 8000rpm so on the last run i tried a higher rpm.
one rotor bearing spun and a rotor tip touched the housing causing one apex to get stuck in the groove.
#298
Rotary Freak
iTrader: (8)
Rotor bearing spun?
Dont use that rotor again. Has anyone played with any of the balancing on the engine etc?
Is it the same rotor that had the smashed tip that damaged a bearing?
What kind of revcut are you using?
Set yourself up a 2 step and set it to 7500rpm and this will solve your bogging issue.
The rotors you had previously? were they new? had someone put bearings in them?
With your new engine. Get .15mm shaved of the tips of your apex seal slots. Gives the rotors abit of movement without smashing it self to bits.
Dont use that rotor again. Has anyone played with any of the balancing on the engine etc?
Is it the same rotor that had the smashed tip that damaged a bearing?
What kind of revcut are you using?
Set yourself up a 2 step and set it to 7500rpm and this will solve your bogging issue.
The rotors you had previously? were they new? had someone put bearings in them?
With your new engine. Get .15mm shaved of the tips of your apex seal slots. Gives the rotors abit of movement without smashing it self to bits.
#299
Daily Used and Abused
iTrader: (1)
Join Date: Dec 2008
Location: South Florida
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
i burnout in second from the get go and dont think itll bog in second i tried and it doesnt(270hp) i take it to 7k and release the clutch and keep it around 5-6k. be careful with first gear burnouts i broke a stubby becasue of wheel hop the tires spin to slow that you have to rev it alot.
#300
Daily Used and Abused
iTrader: (1)
Join Date: Dec 2008
Location: South Florida
Posts: 290
Likes: 0
Received 0 Likes
on
0 Posts
oh and keep up the good work =D i recently got my borg s400sx cant wait to mount it. and ill be tring out the ebay exhaust manifold, ill let people know how that works out.