How to see if turbo is blown?
#1
Rotary Enthusiast
Thread Starter
Join Date: Oct 2002
Location: S.Cali, OC!
Posts: 1,468
Likes: 0
Received 0 Likes
on
0 Posts
How to see if turbo is blown?
How do you check if the single turbo is blown? Either my car is spitting oil in internally and making lots of white smoke...or the turbo seal is blown. But i dont know which one it is. How do i check for these...I know that when i pulled out my spark plugs...and cranked the motor, the front rotor spit out more black stuff then the rear one did.
#3
development
who built the motor?
gas in oil with 0 boost and 1 mile...side seals properly aren't clearanced properly.
or maybe an oil control ring issue...maybe builder installed the springs wrong, could cause oil smoking and possibly fuel to slip into the oil fairly easily.
gas in oil with 0 boost and 1 mile...side seals properly aren't clearanced properly.
or maybe an oil control ring issue...maybe builder installed the springs wrong, could cause oil smoking and possibly fuel to slip into the oil fairly easily.
#4
Rotary Enthusiast
Thread Starter
Join Date: Oct 2002
Location: S.Cali, OC!
Posts: 1,468
Likes: 0
Received 0 Likes
on
0 Posts
quite possibly those rings... me and my friend rebuilt it. but he's built 3 motors previously and those are still running good. I guess i was the unlucky one in the bunch =(
Trending Topics
#11
GrapefruitRacing?
Join Date: Apr 2003
Location: PartSource
Posts: 2,155
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by PhatManBUD
quite possibly those rings... me and my friend rebuilt it. but he's built 3 motors previously and those are still running good. I guess i was the unlucky one in the bunch =(
Did you guys use all new oil control and oil control o-rings?
Did you use the old oil control rings to press in the new ones?
that's about all i can think of right now.
*Edit* Correct me if i'm wrong, but, isn't it expected to burn oil till the engine is broken in and all seals are properly "seated" Now i'm not sure how much oil your burning though.
Last edited by RXciting; 05-11-05 at 11:27 AM. Reason: just remembered
#12
Rotary Enthusiast
Thread Starter
Join Date: Oct 2002
Location: S.Cali, OC!
Posts: 1,468
Likes: 0
Received 0 Likes
on
0 Posts
im pretty sure its supposed to be smoking a bit. but i dont know why it would be smoking to the point where i cant drive it. cause thats just asking to be pulled over. it smokes so much my neighbors ran over to my house cause they thought it was on fire. i believe we used the old ones and put new seals in them.
#13
Senior Member
iTrader: (1)
dude, i having the same problem with the jspec I just put in my car. smokes all the time!!! I think it's the turbo because when I took it off and looked in the manifold it was still clean. try taking the turbo off if it's not to much work, thats one way to tell.
Also, if a turbo had a decent amount of shaft play would that cause it to leak oil because I've gone through 2 turbos both with some shaft play and both smoke, one not as bad as the other but enough thats it's not driveable
Also, if a turbo had a decent amount of shaft play would that cause it to leak oil because I've gone through 2 turbos both with some shaft play and both smoke, one not as bad as the other but enough thats it's not driveable
#14
Senior Member
iTrader: (1)
Join Date: Nov 2004
Location: Austin, TX
Posts: 494
Likes: 0
Received 0 Likes
on
0 Posts
my car started smoking recently at idle only but if i rev up the motor the smoke goes away for a few seconds, no smoke on cold start and no smoke under boost. i have a little bit of shaft play from side to side but it's verry minimal and no in and out play, can anyone tell me if this is my turbo and why it would be smoking? turbo still spools just fine.
#15
Front Range Express
Join Date: Jul 2004
Location: Colorado Springs
Posts: 571
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by KevinW
my car started smoking recently at idle only but if i rev up the motor the smoke goes away for a few seconds, no smoke on cold start and no smoke under boost. i have a little bit of shaft play from side to side but it's verry minimal and no in and out play, can anyone tell me if this is my turbo and why it would be smoking? turbo still spools just fine.
I'm having this problem... here's a link to my discussion in the 3rd Gen forum. I should have checked here first... I'm new to the forum and sometimes don't have the best grasp of the obvious
#16
The king of the highway!
iTrader: (2)
Join Date: May 2004
Location: Home of the 305 Boyz(miami)
Posts: 2,988
Likes: 0
Received 0 Likes
on
0 Posts
IM WAITING ON TO SEE WHAT YOUR PROBLEM IS TO. Cause my car is smoking white smoke so much i cant drive it. Just a rebuild too!. Im thinking its the twins tooo. Thats y im going single . but as they say until you pull that engine you wont know whats wrong
Thread
Thread Starter
Forum
Replies
Last Post
The Shaolin
2nd Generation Specific (1986-1992)
9
09-14-15 07:50 PM