GT500R-SP or GT3574R?
#1
Make an assessment...
Thread Starter
iTrader: (3)
GT500R-SP or GT3574R?
I was looking into the GT500R from A-Spec, and when I talked to Sean and told him what I wanted it for he suggested going with a GT3574R customized for my application.
I will mostly be using it for road course and possibly autocross (I know Rich, I know ), but I want to get decent top end from it too. This will most likely never see a drag strip, and only possibly see a few highway runs (I like going from a roll, that's why). I'm more into spirited backroad drives on curvy roads.
This is what the site says for the GT500R...
These setups are capable of 500whp@20psi with the right combination of build and a proper tune. We have seen 503whp@20psi on a large street ported motor. Most customers will see around 430-440whp in the 15-16psi range. With that 15psi being achieved around 3800rpm leaving you plenty of RPM to have a nice power band.
Sean said the GT3574R would be able to reach 14psi around 3400 and still be able to get up to around 450-500whp but it wouldn't be as efficient as the GT500R. He didn't say that verbatim, but that's what I gathered from information he gave me. Obviously this turbo would be ball bearing, and as I said, he said it would be customized for my application.
Being that the GT500R has great response for a good size turbo, it's really hard to turn your back on this one. However, the GT3574R has even better response and can still get pretty high into HP, just not as efficiently. I'm also getting the screamer pipe rerouted back into the DP, and getting everything ceramicoated. The GT500R kit costs a bit more. The customized GT3574R would be about $100 less.
FYI, I have an agressive streetport, RE monster VMIC, wide open exhaust with only a resonator to quiet it a bit (with GReddy Ti exhaust), 1000cc pri and 1600cc sec, HKS twin power, and more but I'm not sure what all matters for your advice.
So guys and gals, what do you think? Which one? Also, people that have either of these (although the customized one will be hard for someone to have haha), please chime in.
I will mostly be using it for road course and possibly autocross (I know Rich, I know ), but I want to get decent top end from it too. This will most likely never see a drag strip, and only possibly see a few highway runs (I like going from a roll, that's why). I'm more into spirited backroad drives on curvy roads.
This is what the site says for the GT500R...
These setups are capable of 500whp@20psi with the right combination of build and a proper tune. We have seen 503whp@20psi on a large street ported motor. Most customers will see around 430-440whp in the 15-16psi range. With that 15psi being achieved around 3800rpm leaving you plenty of RPM to have a nice power band.
Sean said the GT3574R would be able to reach 14psi around 3400 and still be able to get up to around 450-500whp but it wouldn't be as efficient as the GT500R. He didn't say that verbatim, but that's what I gathered from information he gave me. Obviously this turbo would be ball bearing, and as I said, he said it would be customized for my application.
Being that the GT500R has great response for a good size turbo, it's really hard to turn your back on this one. However, the GT3574R has even better response and can still get pretty high into HP, just not as efficiently. I'm also getting the screamer pipe rerouted back into the DP, and getting everything ceramicoated. The GT500R kit costs a bit more. The customized GT3574R would be about $100 less.
FYI, I have an agressive streetport, RE monster VMIC, wide open exhaust with only a resonator to quiet it a bit (with GReddy Ti exhaust), 1000cc pri and 1600cc sec, HKS twin power, and more but I'm not sure what all matters for your advice.
So guys and gals, what do you think? Which one? Also, people that have either of these (although the customized one will be hard for someone to have haha), please chime in.
Last edited by Zero R; 01-19-09 at 12:41 PM. Reason: See me if needed.
#5
Racing Spirit
iTrader: (2)
Join Date: Jun 2007
Location: NNJ
Posts: 557
Likes: 0
Received 0 Likes
on
0 Posts
well its really hard to give you advice because we don't know what exactly you will use this for. Are you trying to be competitive? you said road race and autocross but which level? For road racing are you in a class that uses a power / weight ratio ? If so then you should revert to the formula to see which turbo you need to accomplish your goal. If your autocrossing with a road racing setup you will not be competitive...
#7
Make an assessment...
Thread Starter
iTrader: (3)
Are you talking about a GT3582 straight from Garrett? Where did you find this?
well its really hard to give you advice because we don't know what exactly you will use this for. Are you trying to be competitive? you said road race and autocross but which level? For road racing are you in a class that uses a power / weight ratio ? If so then you should revert to the formula to see which turbo you need to accomplish your goal. If your autocrossing with a road racing setup you will not be competitive...
So it's kinda hard for me to say what class I want to be in and all that, I need to do more research for that. However, there doesn't seem to be much difference between these two turbos, the one spools a few hundred RPM faster and can still reach 500hp but not as efficiently...the other spools not as fast but still very good, and can reach 500hp with no problem.
My thinking is, there will always be someone out there who is faster, and I'm more into curvy roads, so there's not much need for the 500R for me. Although, there might be that new GT-R or a piece of domesticrap that I might need the extra top end for hahaha.
Trending Topics
#8
Make an assessment...
Thread Starter
iTrader: (3)
But I know what you're saying.
#15
Registered User
Join Date: Dec 2001
Location: Chicago
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
#16
Senior Member
Join Date: Jul 2003
Location: Edmonton, AB, Canada
Posts: 408
Likes: 0
Received 0 Likes
on
0 Posts
I've run his original GT35R kit for the last three years on a road race car. I've put in hour long sessions flogging my FC at 14 psi (about 400 rwhp I think (I only dyno'd at 8 lbs (340 rwhp) and 18 lbs (459 rwhp) so I'm assuming 14 psi is around 400.) Nothing but good things to say about his product. I'd ask him about the Tial hotside if I were you. I think that is going to be a killer combo for the roadcourse.
-Trent
-Trent
#17
Lives on the Forum
iTrader: (8)
I've run his original GT35R kit for the last three years on a road race car. I've put in hour long sessions flogging my FC at 14 psi (about 400 rwhp I think (I only dyno'd at 8 lbs (340 rwhp) and 18 lbs (459 rwhp) so I'm assuming 14 psi is around 400.) Nothing but good things to say about his product. I'd ask him about the Tial hotside if I were you. I think that is going to be a killer combo for the roadcourse.
-Trent
-Trent
thewird
#18
Saiga-12 Power!
iTrader: (4)
Join Date: Oct 2004
Location: N of Chicago
Posts: 4,384
Likes: 0
Received 0 Likes
on
0 Posts
http://www.tialsport.com/prod_tc_tial_d.htm
How would the BB 3574 stack up against the 35RT4 with similar exhaust housings?
To the OP: I'd go with whatever your wallet & Sean recommend.
To the OP: I'd go with whatever your wallet & Sean recommend.
Last edited by Juiceh; 01-19-09 at 04:00 PM.
#20
Rotary tuner
Join Date: Feb 2004
Location: In Sweden
Posts: 124
Likes: 0
Received 0 Likes
on
0 Posts
I would go for a bigger turbine housing becuse the only thing you get in higher rpm is back pressure and heat with a 82A/R housing. With a small turbin housing you get a good spool and great torque BUT the bad thing with a small turbine side is that you get to much power at once so the car is hard to drive.
I tried a GT500R but i switch to a T04Z and the car is mutch more easy to drive with good spool and enough power
I tried a GT500R but i switch to a T04Z and the car is mutch more easy to drive with good spool and enough power
#21
There must be some mystique in naming turbos? Like this one, basically a plain old T04B "P-trim exhaust wheel" with an upgraded GT35R compressor wheel in a T04S cover. A slight twist to the original tried and true "meat and potatoes" 60-1 rotary turbo.
#22
Make an assessment...
Thread Starter
iTrader: (3)
Sean, I had another concern. I heard somewhere that you guys will make sure the turbo and manifold seat together completely, that you machine both sides to make sure they sit flush, is that true? I had a problem with my current turbo and manifold and it kept blowing gaskets or it just wouldn't seal completely, so I got exhaust in the car when I turned the air on, not to mention the sound of an exhaust leak drove me up the wall eventually.
I hope you're asking someone at A-Spec, because I have no idea haha.
I know they make good products, that's why I'm going with them. It's good to hear praises from yet another person with their stuff, makes me feel like I'm pointed in the right direction haha. I also wonder about the Tial hotside, this is the first I've heard of it. Is that an option A-Spec offers?
Yeah that's what I'm thinking, he knows alot more about it than I do, and it helps that he has experience with not just turbos, but rotaries too.
That's the only thing I can see, but I'd like to know if there's more to it than weight difference. Depending on how much of a difference it would be, I might still be interested.
The turbo I've been using has a T67 wheel in a GT35R DBB housing, with a .68 hotside. It spools pretty damn fast and I have no complaints, other than I think I blew the oil seals while it was getting tuned haha. It wasn't hard to drive though. I'd much rather have the power real early than too late and have to wait for it to kick in. Thanks for your input!
I've run his original GT35R kit for the last three years on a road race car. I've put in hour long sessions flogging my FC at 14 psi (about 400 rwhp I think (I only dyno'd at 8 lbs (340 rwhp) and 18 lbs (459 rwhp) so I'm assuming 14 psi is around 400.) Nothing but good things to say about his product. I'd ask him about the Tial hotside if I were you. I think that is going to be a killer combo for the roadcourse.
-Trent
-Trent
Yeah that's what I'm thinking, he knows alot more about it than I do, and it helps that he has experience with not just turbos, but rotaries too.
That's the only thing I can see, but I'd like to know if there's more to it than weight difference. Depending on how much of a difference it would be, I might still be interested.
I would go for a bigger turbine housing becuse the only thing you get in higher rpm is back pressure and heat with a 82A/R housing. With a small turbin housing you get a good spool and great torque BUT the bad thing with a small turbine side is that you get to much power at once so the car is hard to drive.
I tried a GT500R but i switch to a T04Z and the car is mutch more easy to drive with good spool and enough power
I tried a GT500R but i switch to a T04Z and the car is mutch more easy to drive with good spool and enough power
#24
I'd bet if you ran that turbo in the ball bearing version with a 0.84 divided tang. hotside with proper tubular manifold and downpipe, you'd change your mind.