does this sound right? pt-63
01-13-05, 09:45 AM
#1
boost > *
Thread Starter
Join Date: Aug 2004
Location: buffalo, ny
Posts: 1,527
Likes: 0
Received 0 Likes
on
0 Posts
does this sound right? pt-63
k i'm finally gonna order my turbo tommorow 
everything else is already in place and this is the last thing i need for my single turbo project. i'd been kinda bouncin back and forth between the gt40r (no one had them) and the gt35r, but the pt-63 grabbed my attention and i like the price so i think i'm gonna go with that. just wanted a "final opinion" i guess before i go thru with it.
specs can be found http://www.precisionturbo.net/turboc...tegory_id=3027 there, it'd be the pt-63 w/ .96 tang , p-trim, divided housing
here's a relevant mod list to give u an idea of the setup:
street ported motor w/ 3mm seals
hks 50mm racegate, ssqv bov
haltec e6k
rx7 store secondary rail w/ 1600cc injectors
sx fpr
dual walbro intank fuel pumps
custom vmount setup (using mazda comp radiator and a spearco ic)
anything i'm forgetting/ should look into? and what kinda #'s could i expect on pump gas, around 15-17psi ? thanks in advance guys
everything else is already in place and this is the last thing i need for my single turbo project. i'd been kinda bouncin back and forth between the gt40r (no one had them) and the gt35r, but the pt-63 grabbed my attention and i like the price so i think i'm gonna go with that. just wanted a "final opinion" i guess before i go thru with it. specs can be found http://www.precisionturbo.net/turboc...tegory_id=3027 there, it'd be the pt-63 w/ .96 tang , p-trim, divided housing
here's a relevant mod list to give u an idea of the setup:
street ported motor w/ 3mm seals
hks 50mm racegate, ssqv bov
haltec e6k
rx7 store secondary rail w/ 1600cc injectors
sx fpr
dual walbro intank fuel pumps
custom vmount setup (using mazda comp radiator and a spearco ic)
anything i'm forgetting/ should look into? and what kinda #'s could i expect on pump gas, around 15-17psi ? thanks in advance guys
01-13-05, 12:47 PM
#2
Rotary Freak
Join Date: Dec 2001
Location: chandler, AZ
Posts: 2,402
Likes: 0
Received 0 Likes
on
0 Posts
That is actually the turbo that I would most likely go with if I ever change setups. Looks to be a pretty well balanced turbo as far as power potential and spool go.
01-13-05, 02:53 PM
#3
ZZzzzzz...PHshshshssshh
Join Date: Jul 2001
Location: Washington State
Posts: 985
Likes: 0
Received 0 Likes
on
0 Posts
Thats the turbo I'm getting installed now, we're trying to get 500rwhp @ 25psi and trap speed 135mph in the 1/4......https://www.rx7club.com/single-turbo-rx-7s-23/new-ported-motor-single-turbo-project-has-begun-381136/
Last edited by RX7-2JOCK; 01-13-05 at 02:56 PM.
01-13-05, 07:58 PM
#4
Just made 410 rwhp at 15psi with a 63-1/.96/P-trim turbo very similar to the Pt-63.
At 19 psi power was at 474 rwhp. Tommorow with higher boost at C-16 I'll see what that turbo is capable of making.
At 19 psi power was at 474 rwhp. Tommorow with higher boost at C-16 I'll see what that turbo is capable of making.
01-13-05, 08:28 PM
#5
boost > *
Thread Starter
Join Date: Aug 2004
Location: buffalo, ny
Posts: 1,527
Likes: 0
Received 0 Likes
on
0 Posts
awesome, sounds like a good choice then
i ordered it today, to my suprise its not available with the divided housing, but all the other specs i wanted were available, they said it should be built and on its way in about a week and 1/2
i ordered it today, to my suprise its not available with the divided housing, but all the other specs i wanted were available, they said it should be built and on its way in about a week and 1/2
