rdahm

iTrader: (6)

I am looking for the four best (best performance, best reliability, best price, best kit) single turbochargers. I am planning on going single over winter as my project and need expert advice. I am also going to put that infomation onto my website

twinturborx7.com

which after the upgrade would be

turborx7.com

I want the turborx7.com to be a good page all about singles while the twinturborx7.com would be about, obviously, the twins.

Thanks! (posted as well at nopistons)

Conv.WS6

I personally got the To4s System because of the Cast Manifold, and the ease of rebuild of the turbo.
GT35/40 kits seem to be putting 20 more rwhp to the ground though. T78 seems to be another really nice turbo setup, and if you have the money the KKK offered by SR is putting some strong numbers out except it's too high in my opinion. Hope this helps.

Wargasm

Go here and start looking at actual results as a start:

http://www.catenet.net/dyno.php

My picks off the top of my head would be T04S, GT35/40 for 15-20 PSI range.

rdahm

iTrader: (6)

That is one of the best pages i have seen for turbo upgrade questions thanks!

allrotor93

iTrader: (126)

i am real happy with my sr kkk(or whatever the hell it is). it spools pretty damn quick.

Jason

iTrader: (5)

I would go with the T-78 or XS T04S kit. T04S will give you similar HP numbers as the GT35/40 for less money. T-78 will put down more than both but more lag.

Jason

Zero R

iTrader: (1)

If it were my money it would be either a GT35/40 or a GT40R much nicer turbo's than the old school Greddy and TO4s turbo's and it isn't that much more expensive.Not to mention full ball bearing center section.

rdahm

iTrader: (6)

Jason,
What spools at the lowest RPM? If you had the money to spend would it be worth the gt35/40?

I have the Blitz FMIC (from rx7store.net :-)) and what kit will bolt up to that? i have seen that elbow on some kits that bolt to the stock place where the y pipe would.

rx7tt95

GT40, afik, can't be had with a BB center section. Just a plain bearing.

GarageBoy

A Spec is coming out with a BB one

FxF

How about the Apexi AX75 which is used in Imamura's Apexi Drift FD?

A-Spec Tuning

GT40R is ball bearing and we have a kit already made for it. It would be for those who want more than a GT35/40 but spool shouldn't be to far off.

-Sean

BoostedRex

Sean, I've been waiting for you to start letting out some more info on that kit. Exactly how much more are you expecting out of the GT40R vs. the 35/40. My half bp would choke on top end with a 35/40 but the GT40R sounds like it might be the ticket. What's the deal with it? Thanx in advance as always.

Zach

rx7tt95

Is this using genuine Garrett dual ball bearing CRHA's? They do not list that turbo as an option and I remember someone mentioning (Magnus?) that the GT40 bb couldn't be had or wouldn't wor (something to that effect).

Are you able to sell just the turbo? What trim for compressor and the turbine? Thanks in advance.

A-Spec Tuning

I'm still waiting for my turbo's to get here I don't want to give any #'s till I can get one on a car. But I think it might be for you.

-Sean

A-Spec Tuning

They are not listed yet because they haven't released them yet.The GT40 couldn't use the BB center section on wouldn't fit.The GT40R's are full BB.

-Sean

rx7tt95

ETA on arrival? I already have a GT40 compressor mated to my T78 compressor housing and turbine. I don't think it's a perfect match but I love the endless power (once it spools) of this compressor. It really rips up top. If it's a few hundred more than a plain bearing GT40 I might be game. What's the status on people needing rebuilds on their 35/40's? Is it now a bit more feasible?

sub-zero

To4S with a BB option? Parts are simple to get and cheaper I bet.

Zero R

iTrader: (1)

True but the wheels are different and I would put my money on the GT40R before TO4S in the end.

Fatty_FC3S

Since so many people like the Greddy T78 kit because of its flow characteristics, then why dont more people go for the Innovative ballistic dual ball bearing T66?? Isnt that the same specs as a T78 but with a full ballistic Garrett cartridge?? I would think that you would get the awesome top end of the T78, but with less lag.


Anyone care to comment on this??????

the_glass_man

iTrader: (2)

I didn't think Innovative used Garrett cartridges?
Lots of people don't know about the turbos, and they are very, very expensive!

'//icked

Hmm, does anyone else have some more info on this Ballistic T66 Turbo? If it really does have the same topend output of the T78 but spools much quicker... that sounds like the ultimate street setup. I'm sure I'm not the only one interested in this?

A-Spec Tuning

I have 3 Gt40R's in stock, two are for sure spoken for so that leaves one, and yes they are easier to rebuild now.

-Sean

TwinTriangles

between the GT35/40 and the T04s, would it be better to grab a 35/40 being its ballbearing or is the T04s ballbearing also ?
Sorry I dont know turbos well and am just researching a little before winter...

ZoomZoom

iTrader: (2)

I have the GT35/40 and it makes insane power. I really would like to try the GT40R. If it has similar spool charcteristics as the GT35/40 but more power I just dont know what turbo could be better!! And the difference in price is Minimal. We are talking hundreds of dollars not thousands. When your doing a Single turbo upgrade its not about Hundred of Dollars. Its about Thousands. The benefit for Dual Ball bearing turbos outweigh the cost. I am thining about selling my GT3540 and Buying the GT40R Kit.