Went for the subtle "could've come from the factory like that" look. Apex skirts, 18x9.5's, modest lowering on Eibachs and Tokicos.
http://i291.photobucket.com/albums/l...3/DSCN2792.jpg
http://i291.photobucket.com/albums/l...3/DSCN2758.jpg
http://i291.photobucket.com/albums/l...3/DSCN2759.jpg
http://i291.photobucket.com/albums/l...3/DSCN2791.jpg
http://i291.photobucket.com/albums/l...3/DSCN2798.jpg
http://i291.photobucket.com/albums/l...3/DSCN2797.jpg
http://i291.photobucket.com/albums/l...3/DSCN2762.jpg

Hey there, I was wondering if the front fenders will fit flush and smooth on my FD if i dont have sideskirts and dont want any? Also, my car is quite stock and i am wondering if i slap the fenders on, do I have to change the wheel fitment.

I'm after the front fenders and the rear fender flares. How much will it cost to have them shipped to Athens, Greece?

These fenders are very good copies so, they will fit fine. You will definately need to change wheels and tires with this set up.

Very nice YELLOWGSLSE, are the rims 350Z spec? 18x9.5 +20ish?

Wow that is a sweet kit. Definitely would run that if I had an FD.

would the front bar of this kit fit on with the genuine KS auto fenders?

and how much would shipping be to melbourne, australia, postcode 3941?

YELLOWGSLSE!

do you have plans on mounting a splitter inder your front? (might improve cooling)

looks great

Thanks! Is a splitter the same as an undertray? If so, I have the shineauto undertray/splitter. I just haven't installed it yet.

Yes, a splitter is the undertray

Post some more pictures when you get it mounted.

and if you could post temp differences.

keep it up, your car looks great!:icon_tup:

They did a real good job on the rear flares :).

Ken

burnout fenders
 

do u ship to canada? wat are the mm size for front and rear fender flaer in mm? do u have 50mm in front and 30mm rear?

burnout fenders
 

with the burnout kit whats size of rim i would prefer 19 by 12 with 0 offset fit? at the rear and front 19 by 9.5 with a 22mm off set good? pls help

We do indeed ship to canada, but we do not offer fenders as wide as those you are requesting.

19x12 +0 is too aggressive.

About 19x10.5 +22 should be good

19x9.5 + 22 in the front should be fine

rims
 

whats the widest/deepest lip u can possibly put on a burnout fender? with a 10.5 with +22 offset thats about a 4-5 inch lip right? or also, can u go 11 with a 0 offset? or it be stickin out way to much?>

http://www.1010tires.com/WheelOffsetCalculator.asp

the lip will be based on the wheel design so you can't make a generaliztion based on width and offset. use the calculator to see what will fit the same as a 10.5 +22

http://www.1010tires.com/WheelOffsetCalculator.asp

the lip will be based on the wheel design so you can't make a generaliztion based on width and offset. use the calculator to see what will fit the same as a 10.5 +22
__________________
88T2, tec3R, HT200, OS Giken twin, ATS deftforce 1.5way
93 R1 PFC, PFS stuff, regamasters
07 speedtriple 1050




what do u mean? if i want to go bigger from a 10.5 +22 to a 11 inch or even 11.5 rim wouldnt that give me more offset to play with ending up with a bigger lip? or stay with the 10.5 and decrease the offset say 0 offset for more lip ( pushin the rim towards the outside of the car? I JUST WANT THE MAXIMUM LIP SIZE I CAN PUT ON MY BURNOUT FENDER STICKIN OUT JUS LIKE THIS PIC!!!! JELP!!!!!!!!!!!!!!!!!!!!!!!!!

who's car is that in your sig "wpg rx7"
do you know the specs on those wheels?

if a 10.5 +22 is flush with your fender then going to an 11 you will need +28 to fit the same on the outside. most likely you'll have the same lip to play with and thats only with the same style of wheel. there are low offset wheels with no lip and high offset wheels with 3in+ of lip, its more based on the wheel design than the width and offset. in order to assure maximum dish, you'll have to pick the wheels you want to get, install the burnout kit, take some measurements and then custom order the wheels to fit your car. their demo car is running a 19x10+6 in the rear but with a 235 stretched onto it to give you a ballpark of where to start.

wow thanks fcnared explained that real well!!!

1 more question.

whats the biggest offset/lip u ever seen on FD3S? thats what im goin for on my rx7

buzzer,

check here http://viewmorepics.myspace.com/inde...2277&view=true

can prolly ask the owner directly

haha yeah thats my car

sick car phat, inspiration for me :)