bad 83

iTrader: (3)

There were two S4s, and a S4 vert. Pretty rough shape, but surprisingly all still had the engines in them. Even the FB's had there engines and trans. It looked like all the FCs trannies were gone. Weird?

blackdeath647

iTrader: (2)

that reminds me, i need to find someone that wants to get rid of a drivers side tail light lense for my FB, i'm tired of not having a lense, seems like everyone wants to sell the whole tail light assembly tho

bad 83

iTrader: (3)

Both of those FBs there had the tail lights in them I think. You should check them out.

LongsTurboFB

iTrader: (4)

BRAP BRAP BRAP BRAP BRAP BRAP BRAP BRAP BRAP BRAP BRAP BRAP BRAP BRAP :p

LongsTurboFB

iTrader: (4)

Brap v8 killer brap v8 killer brap v8 come get some

bad 83

iTrader: (3)

So what are tring to say? HAHAHAHA!!!!

Jeezus

iTrader: (4)

Here ya go sam, make your beemer like this:

http://www.youtube.com/watch?v=ZsGTBWmN41s

bad 83

iTrader: (3)

That one is pretty cool, but I think this one is a little more like it http://www.youtube.com/watch?v=tRc0mn8OlQw

robs_seven

iTrader: (1)

well i finally got the new rear end apart. One axle was STUCK, but no worries, i got the chunk out and looked it over and it looks to be in good shape. I degreased it and pout POR 15 on it to coat the little rust that was left after wire brushing it. I hope to get my old one out tomorrow and if i have time get that one back in.

bad 83

iTrader: (3)

Cool deal............

dj_silencer200399

iTrader: (2)

Whats guys sorry its been awhile college bs has been taking all my time, haha i had some questions if you guys don't mind. can a t3 or a t4 turbo be a clean replacement for the stock t2 turbo or do u have to change th exhaust manifold too im pretty sure you do im just wondering?

Anthony does that amnual boost controller really make a difference because i got rid of my electronic one and now im only running 9-10 lb.?

I need a turbo downpipe gasket where do i get one?

Thanks you guys r the best!

Where's may's meet at?

BigIslandSevens

iTrader: (4)

Anyone have or know where a S5 N/A tranny is available? Our FC **** it's tranny today on Elizabeth at a intersection. tearing it down now. Thanks to AAA I had to leave work and drive all the way back up to Newton to meet the driver because I had the card with me instead of with her...Fuc AAA cost me a days work and alot of gas!

Jeezus

iTrader: (4)

Hey I got your text. I don't have any transmissions here (yet) but I can ask around if you would like.

Sorry to hear about the thing dying on ya, especially if you had to drive up there. I used AAA once, I never had it but a friend did and he called in, said my car was his, and he towed it to my place. No card/sticker or anything. I think you just got an ******* or something?

workinprogress80

Dave how much would you want if I got you to paint a door and fender on my truck???

bad 83

iTrader: (3)

Hey Dave. PM Long and see what he can do for ya. I know he has some extra parts.

robs_seven

iTrader: (1)

well guys i got my rear end tore apart. It looks like it has a slight bit of wear. Its a little shinier then it was but its not destroyed. There is a ton more backlash then the one sam and i pulled saturday so. The 83' one is going in tomorrow, along with the drive shaft.

BigIslandSevens

iTrader: (4)

I got one from Josh(not Long) Putting it in tonight, just starting on it. Thanks Josh, It dry shifts thru all the gears so that is already better than ours. I believe the 3/4 shift fork has come loose from the shaft( the roll pin broke/fell out) As it happened at a stop with the clutch in stick in N. So I don't "think" it is a major repair. It is just deep in the heart of the beast and I need to make a few tools to get some things apart.

Kory, I would have to see it first as to what repairs need to be done send me some pics or a PM with a desrciption of what's needed.

rx7 SE

iTrader: (5)

Don't know about the turbo. But the boost controller shouldn't really make a difference between electric and manual per se. How much boost are you trying to run? 10 is probably too high on stock injectors and fuel pump...

rx7 SE

iTrader: (5)

So... trying to fix my door tomorrow.. anybody have any ideas on how to get the door open if it doesn't open from either the inside or outside????

rx7 SE

iTrader: (5)

[IMG][/IMG]

Something I built for sophomore design on a CAD system. You would not believe how complicated these engines are to design. I'll be building it this summer with my professors... Stands about 2 inches tall and will run off of compressed air, lol.. should be fun

BigIslandSevens

iTrader: (4)

If you can pull the door panel off you can reach up and grab the rod that controls the latch and pop it open by pushing down on the rod i believe. If down doesn't work , try up That rod may have popped out of its clamp is what it sounds like to me. I have a door handle here we can scavenge for parts if need be.

rx7 SE

iTrader: (5)

Thanks! I'll give that a try in the morning

workinprogress80

PM sent

BigIslandSevens

iTrader: (4)

tranny no workie First I had to swap tail housings since the tranny mount was different than what I have on ours. ( i think this ios actually a S4 tranny) Anywyas, Once I swapped tails, it no shift anymore. I don't see anything wrong with my tail housing but it is not working and I am burnt the fuc out and tired of the bulshat!! goodriddens Tuesday!!

OriGiNaL TyPe R

iTrader: (2)

Yeh, mines did that yesterday and i just hit right below the lock(on the inside on the car) and pulled the lock up and the door open.