Which RteK chip for 6 port turbo? - RX7Club.com - Mazda RX7 Forum

Rtek Forum Discuss the Rtek 2.0 and other Rtek ECU's

Which RteK chip for 6 port turbo?

Reply

 
 
Old 02-06-11, 02:12 PM
  #1
Full Member
Thread Starter
iTrader: (2)
 
John631's Avatar
 
Join Date: Dec 2009
Location: Long Island
Posts: 67
Thanks: 0
Thanked 0 Times in 0 Posts
Which RteK chip for 6 port turbo?

Is it possible to use an RteK chip on an N350 or N351 ECU for a 6 port turbo engine?
John631 is offline  
Reply With Quote
Old 02-16-11, 12:36 AM
  #2
wheres the water goin?
10 Year Member
iTrader: (9)
 
3rd and final 7's Avatar
 
Join Date: May 2005
Location: Nor Cal
Posts: 1,586
Thanks: 0
Thanked 0 Times in 0 Posts
on a n333 i use to use 1.5 with a hi flow fuel pump and raising rate fpr and of course all tii electronics. but you are running higher compression on the s5.
im now running 2.1 same setup and running good.
3rd and final 7 is offline  
Reply With Quote
Old 02-16-11, 11:17 AM
  #3
Rotary Enthusiast
iTrader: (1)
 
Join Date: Jul 2003
Location: ..
Posts: 1,304
Thanks: 0
Thanked 0 Times in 0 Posts
If you turbo an NA, you should use the turbo ECU, MAP and AFM. The ECU, MAP and AFM must all match. Don't mix NA ECU with turbo MAP/AFM or vice versa.
turbo2ltr is offline  
Reply With Quote
Old 02-17-11, 09:59 AM
  #4
Full Member
Thread Starter
iTrader: (2)
 
John631's Avatar
 
Join Date: Dec 2009
Location: Long Island
Posts: 67
Thanks: 0
Thanked 0 Times in 0 Posts
Originally Posted by 3rd and final 7 View Post
on a n333 i use to use 1.5 with a hi flow fuel pump and raising rate fpr and of course all tii electronics. but you are running higher compression on the s5.
im now running 2.1 same setup and running good.
I'm sorry I should have specified i'm running an 6 port s4 block and internals with s5 turbo and intake manifold. I'm not sure what front cover it is but it has the spot for an oil return flange so it must be a turbo front cover... so it doesnt have the really hi compression s5 rotors just the s4 which I believe are only 9.4:1?

To the second reply I was wondering if I could get an NA ECU chipped by RteK so I didnt have to get all the turbo stuff but I guess I cant.
John631 is offline  
Reply With Quote
Old 02-22-11, 11:33 AM
  #5
Rotary Enthusiast
5 Year Member
iTrader: (17)
 
Join Date: Dec 2007
Location: Texas
Posts: 779
Thanks: 0
Thanked 0 Times in 0 Posts
those rotors are still a higher compression than the turbo rotors of any series. As turbo2ltr stated get the turbo ecu, map, and afm. I am running a 6 port turbo as well and have no had any issues with the Rtek 2.1. I suggest you get that one so you have the ability to make adjustments to the map, both fuel and timing. Otherwise in the end you will more than likely end up regretting it.
hiroichi1515 is offline  
Reply With Quote
Old 02-25-11, 01:29 AM
  #6
wheres the water goin?
10 Year Member
iTrader: (9)
 
3rd and final 7's Avatar
 
Join Date: May 2005
Location: Nor Cal
Posts: 1,586
Thanks: 0
Thanked 0 Times in 0 Posts
just run all s4 eletronics rtek 2.1 s4 ecu ( ialso used a 1.5 for a while with a raising rate fpr, boost sensor, afm , im also running a walbro 255 and 720 pri and 740 sec injectors and im doing this on a 88 6 port so you should be just fine , or if you have s5 car you would the turbo electronics for a s5
3rd and final 7 is offline  
Reply With Quote
Old 10-21-17, 11:29 AM
  #7
Full Member
 
Hygoog's Avatar
 
Join Date: Jun 2015
Location: Alabama
Posts: 64
Thanks: 0
Thanked 0 Times in 0 Posts
Originally Posted by 3rd and final 7 View Post
just run all s4 eletronics rtek 2.1 s4 ecu ( ialso used a 1.5 for a while with a raising rate fpr, boost sensor, afm , im also running a walbro 255 and 720 pri and 740 sec injectors and im doing this on a 88 6 port so you should be just fine , or if you have s5 car you would the turbo electronics for a s5
I'm doing a 6 port turbo on my S5. Im using a T04B turbo though. Will a N374 with rtek 1.8 work? This is just temporarily until I get an adaptronic. I wont be boosting much maybe 5-7psi external wastegate.
Hygoog is offline  
Reply With Quote
 
 
 

Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
hotshot2014
New Member RX-7 Technical
8
07-18-17 03:30 PM
smikels
Rtek Forum
4
05-12-16 01:34 AM
Sammy Built
3rd Generation RX-7 (1993-2002) Parts
20
09-08-15 04:08 PM
eddierotary
Rtek Forum
1
08-25-15 06:48 PM
baconflavored
SE RX-7 Forum
0
08-12-15 01:07 AM


Thread Tools
Search this Thread
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -5. The time now is 11:17 AM.


All content Copyright 2007 by Internet Brands, Inc. We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: