View Poll Results: which car has the fastest top speed stock?
3RD generation RX-7
2
40.00%
3000gt vr4
1
20.00%
Supra
0
0%
Skyline R-33 GTR
2
40.00%
Voters: 5. You may not vote on this poll
how can i upgrade my twins for a 3rd gen.
#1
Rotary Freak
Thread Starter
Join Date: Mar 2003
Location: GLENDALE, CA
Posts: 2,274
Likes: 0
Received 0 Likes
on
0 Posts
how can i upgrade my twins for a 3rd gen.
i want to know the max boost (psi) that the stock twin turbo's can handle if i do the best upgrade to them. i want my car to push about 350+ hp . right now i have a punched out cat (both of them, new act clutch, took out the air pump, intake, hks BOV, Greddy intake elbow, and i will soon get a apex power fc with injectors. how can i make it 350+ hp without the power fc because i will get that in a few months (its too expensive $1200!!!!!!!!!). what can i do to the car so it will be 350+ hp then i can increase more. please tell me upgrades that wont end up costing me $3000+ because i can ust go single! thanks for all your help and please tell me how reliable the car will be after i do each one.
thanks
thanks
#2
WTB** Very Low Miles 94-95
Join Date: Jul 2001
Location: Tejas
Posts: 3,298
Likes: 0
Received 0 Likes
on
0 Posts
upgrading your twins is almost as expensive as going single.
you will need almost my entire mod list...yer gonna drain the bank account on this project.
keep aside 500-1000 dollars for tuning if you cant do it yourself with the datalogit.
jason
you will need almost my entire mod list...yer gonna drain the bank account on this project.
keep aside 500-1000 dollars for tuning if you cant do it yourself with the datalogit.
jason
#3
Hey, where did my $$$ go?
Join Date: Feb 2001
Location: Bimingham, AL
Posts: 4,413
Likes: 0
Received 0 Likes
on
0 Posts
you never going to make a reliable 350rwhp without a computer upgrade. you can try using a upgraded Pettit ecu with the unlimited chip and making a manual boost controller. Buy it used for $400-500 then sell it for the same when you get the PFC.
Thats about the cheapest route. As for the turbos, you dont need to touch the turbos for 350rwhp unless they are fucked up
Your going to need a new IC, especially in the summer. In addition your fuel system is going to be on edge, you'll need a new pump at the very least. Do you have a dp and catback? You didnt list them i dont think and you'll need them to run the boost it takes for 350rwhp....which is around 14-15psi. You'll probably also need an ignition amp
Good Luck
STEPHEN
Thats about the cheapest route. As for the turbos, you dont need to touch the turbos for 350rwhp unless they are fucked up
Your going to need a new IC, especially in the summer. In addition your fuel system is going to be on edge, you'll need a new pump at the very least. Do you have a dp and catback? You didnt list them i dont think and you'll need them to run the boost it takes for 350rwhp....which is around 14-15psi. You'll probably also need an ignition amp
Good Luck
STEPHEN
Last edited by SPOautos; 05-02-03 at 05:08 PM.
#4
Rotary Freak
Thread Starter
Join Date: Mar 2003
Location: GLENDALE, CA
Posts: 2,274
Likes: 0
Received 0 Likes
on
0 Posts
i have a question SPO, can the stock twins without being upgraded run 14-15 psi? let me get this strait, all i need to make the twins run 14-15 lbs of boost is a fmic, catback sys, downpipe, any kind of computer that is upgraded,a upgraded fuel pump (do i need new injectors or not and if yes, where can i get the whole kit from?), and a ignition amp? what does a ignition amp do anyway? thanks for all your help, i really appreciate it!
Thread
Thread Starter
Forum
Replies
Last Post
HalifaxFD
Canadian Forum
126
05-09-16 07:06 PM