aerodynamic improvements
#1
Full Member
Thread Starter
iTrader: (4)
Join Date: Feb 2001
Location: Irvine, CA , USA
Posts: 173
Likes: 0
Received 0 Likes
on
0 Posts
aerodynamic improvements
I'm looking for ideas for a 3rd gen to improve the downforce on the car. I noticed a large improvement in high speed stability when I added the R1 lip, but now I'm going to take it to the next level. So any ideas for front splitters and reinforcements to the splitter so that it actually applies force to the chassis? Also any ideas for rear wings? I've been looking for Aluminum of carbon aerofoils that could be used to build a wing, however I havn't been successfull in finding any.
Matt
Matt
#2
Senior Member
Join Date: Dec 2001
Location: Los Gatos, CA
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
i use a mazdaspeed gtc wing, which is adjustable somewhat. it has a low, med, and high incident angle adjustment. i've notice a significant amount of downforce at 80mph and above. i notice this in that at my recent track event, i had to dial down the the downforce to prevent scary understeer in the higher speed corners. this was a temporary bandaid to a tire problem, but nonetheless demonstrated to me that the wing was functioning quite well.
good luck
fabian
good luck
fabian
#3
I am surprised that no one has made some sort of aero foil that can be bolt on under the hatch that sticks up upward when the hatch is closed. Kind of a nascar spoiler/foil except it is mounted under the hatch and sticks out when the hatch is closed.
#4
Old [Sch|F]ool
How about this...
When you run on-track, you must have your windows rolled down. (Unless you're drag racing which is just the opposite... but that's another topic) This tends to create a high pressure area in the hatch area, as anybody who's had the rear carpet come forward and smack them in the back of the head while tooling along the backstretch can tell you.
Why not make a spacer so that the rear hatch stays open a few inches, allowing this high pressure to bleed out over the rear deck, negating some/all of the natural low pressure area at the back of the car that creates lift.
Just a thought...
- PJ (And has anyone else noticed greater high-speed stability with the sunroof popped up?)
When you run on-track, you must have your windows rolled down. (Unless you're drag racing which is just the opposite... but that's another topic) This tends to create a high pressure area in the hatch area, as anybody who's had the rear carpet come forward and smack them in the back of the head while tooling along the backstretch can tell you.
Why not make a spacer so that the rear hatch stays open a few inches, allowing this high pressure to bleed out over the rear deck, negating some/all of the natural low pressure area at the back of the car that creates lift.
Just a thought...
- PJ (And has anyone else noticed greater high-speed stability with the sunroof popped up?)
#7
Rotary Freak
iTrader: (10)
My neighbor who used to race C4 Vettes used a metal prop/bracket that opened the rear hatch about 1". The hatch would lock into place with a clip to secure the lid (rear hatch), and then a metal bar to the lower body attachment point. Basically an adapter to create a 1" gap.
GNX7
GNX7
Trending Topics
#9
Living life 9 seconds at a time
iTrader: (2)
Join Date: Feb 2001
Location: Abingdon, Md
Posts: 6,541
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by djantlive
I am surprised that no one has made some sort of aero foil that can be bolt on under the hatch that sticks up upward when the hatch is closed. Kind of a nascar spoiler/foil except it is mounted under the hatch and sticks out when the hatch is closed.
I am surprised that no one has made some sort of aero foil that can be bolt on under the hatch that sticks up upward when the hatch is closed. Kind of a nascar spoiler/foil except it is mounted under the hatch and sticks out when the hatch is closed.
#10
inteligent extratarestril
Join Date: Mar 2001
Location: The Sunny B.O.P, New Zealand
Posts: 1,313
Likes: 0
Received 0 Likes
on
0 Posts
on a FC, dunno about a FB or FD haven't taken much notice, just open the hatch and put a couple of solid rods from the hatch onto the boot floor, you'll get some MEAN downforce with that huge **** thing deflecting air upwards, but be careful cause it'll suck back alot of exhuast gases. bawahahaa
#11
Old [Sch|F]ool
You'll find that the in-hatch area has a much higher pressure than the above-deck area. The high pressure air from inside the car rolls out over the deck and reduces the low-pressure area over the deck, reducing downforce, as well as the fact that the open hatch reduces windspeed over the rear thus reducing the low pressure area in the first place. (probably why you notice the air sometimes flowing "backwards" INTO the cabin)
#12
Full Member
Join Date: Mar 2001
Location: Marietta, GA
Posts: 222
Likes: 0
Received 0 Likes
on
0 Posts
I'm not an aerodynamic engineer, but based on looking at the current ALMS and Grand-Am cars (as well as places like www.mulsannescorner.com ), the place to focus is underneath the car. The object being to keep as much air as possible from getting under the car, and aggressively evacuating there air that does get beneath it.
.02 cents.
Steve C.
.02 cents.
Steve C.
#18
Rotary Motoring
iTrader: (9)
You'll find that the in-hatch area has a much higher pressure than the above-deck area
Hmm, on an FC there is definetely ALOT more downforce on the rear hatch then inside the cabin. I have tried driving w/ the hatch open and it slams shut once you get up to around 40mph- even w/ the side windows down. If you look at "the FC diagram" you can see there is a high pressure area at the rear lip of the hatch right where it transitions to the flat rear deck. Interestingly there is even a concave area in the glass there- I don't know if that is just a by product of the molding system or if Mazda actually tailored that area for aerodynamics.
Mazda did certainly use the wind tunnel a bunch on the FC. .30 Cd is still awsome 16 years later! I would not doubt the FC is actually aerodynamically better than the FD. Does anyone know how they really compare?
Hmm, on an FC there is definetely ALOT more downforce on the rear hatch then inside the cabin. I have tried driving w/ the hatch open and it slams shut once you get up to around 40mph- even w/ the side windows down. If you look at "the FC diagram" you can see there is a high pressure area at the rear lip of the hatch right where it transitions to the flat rear deck. Interestingly there is even a concave area in the glass there- I don't know if that is just a by product of the molding system or if Mazda actually tailored that area for aerodynamics.
Mazda did certainly use the wind tunnel a bunch on the FC. .30 Cd is still awsome 16 years later! I would not doubt the FC is actually aerodynamically better than the FD. Does anyone know how they really compare?
#19
male stripper
iTrader: (1)
the hatch area is not as high pressured as one would believe. carpet is easy to lift. i popped my hatch and left it stuck to the seals on my sa (damn thing never pops up anyway) and drove around the expressway at 80+. it never vented or broke the seal. now anyone who opens these knows that they don't require a large amount of force to open, so the pressure isn't causing more then maybe less then 10 lbs of lift. i know a guy in nashville had a custom aluminum front lip that had the small adjustment rods on it so that he could adjust the angle of attack. i also agree with qwck10th on making a front and rear diffuser. the front is pretty sinple and can be made from 1/8" plastic sheets utilizing mounting points that already exist under the car. th rear is a little harder as in you want to avoid the exhaust. this will smooth airflow out underneath the car reducing drag.
#20
Full Member
Join Date: Mar 2001
Location: Aliso Viejo, CA
Posts: 135
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by BLUE TII
Mazda did certainly use the wind tunnel a bunch on the FC. .30 Cd is still awsome 16 years later! I would not doubt the FC is actually aerodynamically better than the FD. Does anyone know how they really compare?
Mazda did certainly use the wind tunnel a bunch on the FC. .30 Cd is still awsome 16 years later! I would not doubt the FC is actually aerodynamically better than the FD. Does anyone know how they really compare?
#21
Rotary Motoring
iTrader: (9)
Interesting. Everything I have read said standard FC had a .31 and the sport aero package dropped it to .29 (lower lip extended infront of tires, spats behind the front wheels, in front of the rear wheels and a very low flat spoiler).
FD does appear to be wider- so it has more frontal area aerodynamics has to make up for?
FD does appear to be wider- so it has more frontal area aerodynamics has to make up for?
#22
Ex fd *****
BLUE TII:
The FD may be slightly wider at the rear (vs fc) but has a MUCH lower roof line and looks to be less frontal area.
Fluxen:
The FD .29 cd is indeed for a CLEAN (no wing/spoiler) fd the R-1 front lip adds hardly any drag but offer a significant improvement in front downforce. The stock 93-5 rear wing is a disaster, lots of drag (cd to .32) and little or no downforce.
The FD may be slightly wider at the rear (vs fc) but has a MUCH lower roof line and looks to be less frontal area.
Fluxen:
The FD .29 cd is indeed for a CLEAN (no wing/spoiler) fd the R-1 front lip adds hardly any drag but offer a significant improvement in front downforce. The stock 93-5 rear wing is a disaster, lots of drag (cd to .32) and little or no downforce.
#23
Full Member
Join Date: Oct 2001
Location: Madison, AL
Posts: 180
Likes: 0
Received 0 Likes
on
0 Posts
So, what is a good aftermarket rear end wing that doesn't increase drag (much) but does add downforce.
I just don't like the FD's without the rear spoiler and I don't want a giant Dragster style wing on their either.
Note, I'll probably only road race once or twice a year. Looks are more important to me. Also, cost. I'm basically happy with the Stock touring looks, but I'll be repainting this winter (hopefully) and thought it was a good time to ask.
Thank in advance!
I just don't like the FD's without the rear spoiler and I don't want a giant Dragster style wing on their either.
Note, I'll probably only road race once or twice a year. Looks are more important to me. Also, cost. I'm basically happy with the Stock touring looks, but I'll be repainting this winter (hopefully) and thought it was a good time to ask.
Thank in advance!
#24
Rotorhead
Join Date: Feb 2001
Location: Charlottesville, Virginia, USA
Posts: 9,136
Likes: 0
Received 39 Likes
on
33 Posts
Originally posted by peejay
How about this...
When you run on-track, you must have your windows rolled down. (Unless you're drag racing which is just the opposite... but that's another topic) This tends to create a high pressure area in the hatch area, as anybody who's had the rear carpet come forward and smack them in the back of the head while tooling along the backstretch can tell you.
Why not make a spacer so that the rear hatch stays open a few inches, allowing this high pressure to bleed out over the rear deck, negating some/all of the natural low pressure area at the back of the car that creates lift.
How about this...
When you run on-track, you must have your windows rolled down. (Unless you're drag racing which is just the opposite... but that's another topic) This tends to create a high pressure area in the hatch area, as anybody who's had the rear carpet come forward and smack them in the back of the head while tooling along the backstretch can tell you.
Why not make a spacer so that the rear hatch stays open a few inches, allowing this high pressure to bleed out over the rear deck, negating some/all of the natural low pressure area at the back of the car that creates lift.
Originally posted by peejay
(And has anyone else noticed greater high-speed stability with the sunroof popped up?)
(And has anyone else noticed greater high-speed stability with the sunroof popped up?)
Thread
Thread Starter
Forum
Replies
Last Post
Jeff20B
1st Generation Specific (1979-1985)
73
09-16-18 07:16 PM