Power FC DL and M-300 help needed
#1
Junior Member
Thread Starter
Join Date: Jul 2003
Location: Okinawa/Misawa Japan
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
DL and M-300 help needed
i need to find a map to start with for my datalogit. i just put a TO4R on my 7 with twin fuel pumps/ and fuel presure regulator, 3 core intercooler normal stock injectors, full set of Defi gauges, the M-300 wide band. i also put the 3bar map sensor in and changed my setting to option 1 on the commander. i got the PFC boost controler as well but i kinda need some help getting a beggining map so i don't blow my engine while fine tuning. any help with this would be greatly appreciated.
i also can't figure out where to put the 2 wires that come off the PLX M-300 wide band, i know they need to be connected to the datalogit but not sure which holes to conect them too on the DL.
i also can't figure out where to put the 2 wires that come off the PLX M-300 wide band, i know they need to be connected to the datalogit but not sure which holes to conect them too on the DL.
#2
Eye In The Sky
iTrader: (2)
Join Date: Feb 2001
Location: In A Disfunctional World
Posts: 7,895
Likes: 0
Received 114 Likes
on
66 Posts
You only need to connect the M-300 5volt output to the AN1 DL input. Then you need to calibrate the DL to the M-300. But there is more you can do for more stable readings.
Since you have a DL, have you looked at;
http://sports.groups.yahoo.com/group...k%20Westbrook/
where I talk about the M-300, or have you done a search here for it?
Since you have a DL, have you looked at;
http://sports.groups.yahoo.com/group...k%20Westbrook/
where I talk about the M-300, or have you done a search here for it?
#5
Eye In The Sky
iTrader: (2)
Join Date: Feb 2001
Location: In A Disfunctional World
Posts: 7,895
Likes: 0
Received 114 Likes
on
66 Posts
When you buy it, they are suppose to be added to the group, but they are slow doing it. Keep contacting them about it at : http://www.fc-datalogit.co.nz/
Originally Posted by ghostrx7
Chuck how do I become a member of the datalogit group?...on yahoo that is.
#6
Junior Member
Thread Starter
Join Date: Jul 2003
Location: Okinawa/Misawa Japan
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
thank you for your help. there are 2 wires coming from my M-300 box. one is white and the other is grey. not quite sure which one to connect to the AN1. would you know which one to connect?
#7
Eye In The Sky
iTrader: (2)
Join Date: Feb 2001
Location: In A Disfunctional World
Posts: 7,895
Likes: 0
Received 114 Likes
on
66 Posts
As per the instructions that come with the unit:
White = wideband linear output
Gray = narrowband output
Red = +12VDC
Black = Ground
White = wideband linear output
Gray = narrowband output
Red = +12VDC
Black = Ground
Originally Posted by BillyBoy69
thank you for your help. there are 2 wires coming from my M-300 box. one is white and the other is grey. not quite sure which one to connect to the AN1. would you know which one to connect?
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
David Hayes
3rd Generation Specific (1993-2002)
13
09-05-22 12:45 PM