Siraniko

iTrader: (13)

hey where's jesus. I want to see what his duece can do OR is it just for show

ultimatejay

iTrader: (1)

Well lets see...... over 1 year of car running and no timeslip= show car.

rXc3|\|tR1c

Just a quick question. Did you use spacers either side of your heim joints for your links? Or alternatively, have you got any better pics of the mounting points?

Tone

ultimatejay

iTrader: (1)

Yes, I had to use spacers on both sides and also had to have the spacers go thru the inside of the heim joint because we couldn't find any metric heim joints to fit the factory 14mm diameter bolts. We used I think 3/4" heim joints and then machined the spacer inner diameter to 14mm and then whatever the side clearances was. Here are some pics. It set me back big bucks because we used all chromoly heim joints and then the labor for the spacers. You can save money buy using the regular metric heim joints for 14mm. Here are some pics.

ultimatejay

iTrader: (1)

It also would be a good idea to strengthen the brackets for the links on the stock frame as circled in this pic. As you can see they are pretty thin and weak. I was going to do it but I wanted to dial the rearend in first. Those stock brackets will not handle very many 10k launches on slicks for very long.

rXc3|\|tR1c

Sweet, thanks for the info and pics

84gslsee

iTrader: (1)

Hey Jay, Thanks ! for the thread. Your car is Bad *** !! I just got my RX2 fired up that I bought from blackrotor last month. It's a bridgeport 12a, with RB road race header, wide open, can you say Deafening !! I'm interested in your exhaust setup. are your using road race header ? whats your tube length before the collector ? Are you running 1 or 2 presilencers ? After the collector what side tubing are you running to the 3" muffler ? Any pictures you could post would be great ! I love your video's. I just installed the RB Holley intake and 600 4 barrel, it came with the car, in the trunk. It went from stock Nikki carb, that would only run for 10 seconds like **** and stall to a screamer. I'm just waiting for the coolant seals and linkage plate from RB. Down the road I want to install the IDA, but for know i'm going to play with this setup. When I get it stable, I'll post a video of the open header. Thanks for sharing with all of us.

ultimatejay

iTrader: (1)

Thank you. I have some pics of the exhaust back in my thread somewhere.
I am running the RB roadrace header and then 3" all the way back to a 3" RB high flow stainless muffler. No precilencer. It is pretty loud but runs pretty good. The RB header is not the best but it does pretty good. I could play withe the exhaust and probably get a few more ponies out of it, but I will wait until all the other things are dialed in first. You don't just want to run open headers as you will acutally lose horsepower. Alot of all motor drag guys will use about a 2-3+ foot section after the header and then megaphoning into one 3- 4"muffler. If you have a street car then I would suggest what I am running but put a RB precilencer in the middle. This will give good performance and it will still be loud but bearable. If you want all out performance and noise isn't an issue, then I would recommend a short megaphone system into a high flow muffler or even open. RB makes the megaphone pipe that bolts right up to their header. Good luck.

Regarding the rearend brackets, I have paper templates with all the specs if you want I can mail them to you.

ultimatejay

iTrader: (1)

Ok, ready to hit the track. Aiming for this thursday night at Irwindale again. Going for 7's so wish me luck. I installed my new line lock and the larger 24" tires and it looks much better. I will finally be able to do a decent burnout now and launch. Will have video of the runs so stay tunned. Heres a quick pick of the linelock install.

ultimatejay

iTrader: (1)

Thread update. Ran my PB of 7.83 in the 8th last night!!!! That's a very low 12 second pass in the 1/4.

Here's the vid of the pass. http://www.youtube.com/watch?v=Y0Yk60BGK64

84gslsee

iTrader: (1)

Congrats !! Just a 10th or 2 from 11's

repumax

iTrader: (3)

Sweet bro. Your car sounds sic!

ultimatejay

iTrader: (1)

Thanks guys.

n0ferz

iTrader: (4)

Hey, do you know how many HP is your engine pulling ???

ultimatejay

iTrader: (1)

The last time I dynoed the car I made 197 to the wheels, but that was a long time ago and I have made huge improvements since then. Back then I was running 8.5 to 8.6 in the 8th with low 80 mph. Now my time is 7.83 at 87 mph. So I would say I'm making over 220+ to the wheels now. My dyno is the drag stip now.

Jaime Enriquez

You gotta love "old skool" alternator throttle cable bracket!!!!

Props homie!

n0ferz

iTrader: (4)

wow those are nice numbers if you ask me . I am trying to hit those numbers myself in the future with my 12a rotary starlet

I will keep checking this thread to get ideas of what to do to achieve that

DriveFast7

iTrader: (1)

That sounded great. Nice work Jay.

ultimatejay

iTrader: (1)

Thanks, yeah someday I'll put a nice throttle bracket on, but it does the job.

Thanks bro.

rex3

iTrader: (2)

Car sounds nice... What's your 60ft time?

ultimatejay

iTrader: (1)

Thank you, my 60 ft was a 1.56- I have room for improvement there for sure.

61620B

going tomorrow jay......

REPUZENTN

iTrader: (1)

Awesome #'s Jay! I see that your running the DLIDFIS. I need to do that to my REPU.

ultimatejay

iTrader: (1)

Not this week. I'm still trying to recover from the whip lash to my neck from all those hard launches. Maybe next week.

84gslsee

iTrader: (1)

Jay, what is the weight of the car with you in it ? On this calculator I found, 2300lb car and driver at 7.83 ET says 249.43 HP.


http://www.theddddirectory.com/calculators.php#