13b turbo into rx3
#1
Junior Member
Thread Starter
Join Date: Mar 2004
Location: Brisbane, QLD Australia
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
13b turbo into rx3
I want do start a project rx3 when i sell my series 5, and want to know where i can find step by step instructions on how to fit a 13b turbo engine in, including parts list if possible. would an rx2 be the same steps. any help?? websites, books...
#2
Senior Member
do the project with the rx3 much more room and you will save alot of money becuse u wont have to fabricate to many things.i did the 13b-re swap into my r100 and it is a pain in the butt..with the rx3 u wont need to many things
#3
Senior Member
since u are in australia u shouldnt have to much trouble there are so many shops there that do that engine swap if you want i can give you a friend of mines number he has helped me with so much info and he is in australia also..got to www.mrenforcer.com.au
#4
Junior Member
Thread Starter
Join Date: Mar 2004
Location: Brisbane, QLD Australia
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Thanks. but do you know of a site that i can have a read off first so i got half an idea when i am talking to him.
what mods? what sought of power are you making and times are you running?
any pics?
what mods? what sought of power are you making and times are you running?
any pics?
#5
Senior Member
just tell him you want to put a 13b turbo in your car and what is needed,as for my car its still in the works,needs a rearend that can handle the power but looking at about 350 to 400 at the wheels with 18psi
#6
I belive 300hp is more then enough for a street t2 car, that is old school.
I have a buddy that is pushing 315hp at 12psi of boost I belive. It brings his front end up a little bit.
I have a buddy that is pushing 315hp at 12psi of boost I belive. It brings his front end up a little bit.
#7
rx-3 Turbo
Matt,
I am in the same boat you're in. I do have a 77 SP and I do have a twin-turbo (94TT ported w/aluminum flywheel and moroso aluminum oil pam). It fits perfectly. Is is not turbo yet as I am also looking at which turbo manifold ect will fit. It is currently running with a j-tech intake and 750 carburator. Not exactly what I want but I can move it in and out of the garage. I do have the fuel injected intake and this is where I also have quations. Whether to piece meal it with ordering a turbonetics turbo and have some one fabricate a turbo manifold and go from there or order a complete 94 RX7 TT kit from XS engineering. Of course you will always have to order intercooler, bigger jets, fuel pump, computer, etc. So far I have not found a how to do it book.
You are pretty much on your own here. Good luck. I should make a decision as to which turbo I order within the next few weeks. I'll let you know how my project goes.
Good Luck!
I am in the same boat you're in. I do have a 77 SP and I do have a twin-turbo (94TT ported w/aluminum flywheel and moroso aluminum oil pam). It fits perfectly. Is is not turbo yet as I am also looking at which turbo manifold ect will fit. It is currently running with a j-tech intake and 750 carburator. Not exactly what I want but I can move it in and out of the garage. I do have the fuel injected intake and this is where I also have quations. Whether to piece meal it with ordering a turbonetics turbo and have some one fabricate a turbo manifold and go from there or order a complete 94 RX7 TT kit from XS engineering. Of course you will always have to order intercooler, bigger jets, fuel pump, computer, etc. So far I have not found a how to do it book.
You are pretty much on your own here. Good luck. I should make a decision as to which turbo I order within the next few weeks. I'll let you know how my project goes.
Good Luck!
Trending Topics
#8
Junior Member
Thread Starter
Join Date: Mar 2004
Location: Brisbane, QLD Australia
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Thanks, but i am still after the website that gives in detail step by step instructions on how to fit the 13b turbo into the rx3 engine bay. it tells you what you need and any fabrication (i.e cutting of panels, cross member) that needs to be done.
Thread
Thread Starter
Forum
Replies
Last Post
KAL797
Test Area 51
0
08-11-15 03:47 PM