Yeah, but it's not SC'd anymore. Getting ready to go turbo. Probably take it off the road sometime next month for the conversion.

took it to play with other sevens. I think she had a good time.

Well I cleaned up the garage to make some room for next weeks work. I fixed the GSL-SE oil pan sump. It had been flattened out when the guys at the junkyard pulled the motor. I also cleaned up the oil cooler and found some cracks on the thermostat housing that will need to be repaired before use. While I was at it I started modifying the oil pickup tube with a bell mouth bottom and am looking to modify the oilpan a bit since it will be usede for drag racing. Looking to weld a forward facing vane in there to keep the oil around the pickup during those nice hard launches.

Enjoyed sweet victory of having an exhaust ticket dismissed

I win

test fired my money pit for the first time in yrs. great success

Changed the started in my Vert.

got my 5 mil spacers so i can now run madd camber :)

Started sanding down the lips on my wheels so i can re polish them.

Reconnected a wire to the CPU that had been cut to run a turbo timer with the stock alarm. The list of things to fix is down to 9 :o/

tried another float adjustment, but idle is still good and blipping the throttle it still bogs and tries to die. Arghhhh!!!!

finally removed the 2 lower collars on my front coilovers and installed my five mil spacers...
and now my rims arent flush with the added camber. someone find me 15 mil bolt on spacers?

http://c2.ac-images.myspacecdn.com/i...a768937cb9.jpg

http://c2.ac-images.myspacecdn.com/i...2786490ee9.jpg

Looks good LOW.... is it riding on bump-stops at this point?

fixed, my shit. no more exhaust leak........ for now....

Fuel lines and tank
 

Tonight I crawled under her and dropped the tank, pulled the feed lines and inspected the inside. Found a screen floating around in there that PO must have tried to adapt to the tank. Removed it, plumbed new braided stainless lines blew out feed,vent and rerturn lines and re-connected all. Going back out later to test.:icon_tup:

what did i do today to my rx7 today
 

got in a burnt motor to replace some parts on my locked up motor. hopefully i can mix and match to make a good motor.

lowered on megan track coils. removed two lower collars to get the drop right in the front. lowering the rears tomorrow

told one of them it has till sunday to gimmie some sort of reason to keep it rotary, and then worked on the v8 one

started building my new exhaust well the rear section any ways im designing a quick swap system for the rear option #1 over the Axel to a magnaflow option #2 under the Axel to the magnaflow to see if i like it option #3 under the Axel to a straight pipe with a walmart resonated tip

all in 3 in and for the under the Axel options the 3 in pipe will be kind of smooshed so its oval shaped for clearance reasons and started milling the header flange for my custom header thats about it ill have pics when its done b4 and after

Installed my moderized tail lights that I just finished doing and looked at her. Oh and corksport found me two good rotary housings. I'll be reciving my exhaust system from corksport at the rx7 meeting and the housings.

put a new brake master cylinder in. Now just need to bleed the brakes. She stops much better already and HOLDS pressure :) . . . .

finally drove it after installing the new lower harness. then it randomly lost spark an hour later. thinking it might be a bad ecu ground. i have the phantom 5 repeating beeps :(

Just bought a new black carpet for my FC and put some parts on craigslist.

Parting out my FD, a sad day

got my idle back to about normal. was bouncing at 500 and stalling out when I turned the wheel to fast with the brake on.

hooked up everything! gonna pull start her ass tomorrow. and then stared and drooled a little bit

i rebuilt a carbie for my old rx7 that my buddy has..

https://www.rx7club.com/attachment.p...1&d=1264873641
https://www.rx7club.com/attachment.p...1&d=1264873641

Looks like fun. Gotta love those Nikki's!

test fitted and rolled around on some r32 nissan skyrine gtr rims. i was suprised with how good they fit and look.

http://i270.photobucket.com/albums/j...0128001814.jpg

jawlz.
buy these damn wheels.

Haha I could of told you that. One of the guys at the Drift Office in Auburn took his rims off his Gt-R32 and put them on his FC.

Um sat and looked at my FC trying to figure out how in the fuck I install the front Tow Hook. Looks like it might be fabrication time. damnit owell for dirrect bolt on.

Picked up an FC rad and FC leading coil for the project. Thanks for the Idea Adrian.

Pulled the new project (85 GS)under the carport and dropped in the motor. :)

https://www.rx7club.com/nw-rx-7-forum-33/build-thread-progress-my-car-lots-pic-865772/page3/

Thats what I did! ChECK IT. Give me comments and tips!

did the little bit of body work and primed the trunk lid on my SP,ground down a crack where the body kit was blended to the rear quarter on my wide body,started body work on the right door of my SP.i did pick up the new stripe kit i had made for my SP,only one little mistake,so that part is getting remade,being out of work,i have lots of time to work on both cars.i will post some pics tomorrow.

I walked into my garage to get a 7up and noticed..oh i have TII that i havent touched in 2 years because it hasnt ran in awhile. Then I opened the door and sat in the driver seat, and now I am sad because I want it running..like NOW.

still trying to figure out how to put the damn tow hook on the front.

dug out some stock intake manifolds I had laying around, and cleaned and stripped one, the did the "Naked Nikki" thing and pulled all the emission crap and unnecessary crap off it. Then was going to connect the exhaust and mount everything up, but the heat exchangers/exhaust manifolds I have are too long! Apparently the pre-85 are different, or the one on my 84 wasn't an from an 84. Either way, my "Good feeling" about all the progress I was making kinda fizzled.

Top secret stuff :shiftyeyes:

What are you up to Mark?

bought her some gifts hoping she'll love me as much as I love her. who ever said money can't buy you love never owned an RX-7

I have so many projects right now, its not even funny :(

I thought about it... missed it... Wished I could see it, and drive it. and then I almost cried cause I love my car

replaced windsheild wiper, got some grease to repack the bearings, and all grease fittings.

i did nothin// but dustin . left drifter took over the fmic and turbo upgrade job.. the other dude gave up ,,,, the super 7 should be done soon now . well i did fork out more dough/ thats what i did . spoolin soon .10mm

RE Amemiya Mirrors FTMFW!
https://www.rx7club.com/picture.php?...ictureid=20219
https://www.rx7club.com/picture.php?...ictureid=20218

lol. Got some metal to construct the p-port jig. We'll be crankin them out like muffin tops in no time at all. Man tooling is pricey!! But it hasd to be if you want it done right every time.

i drove my 7 to Stayton to work on his 7. 2 for 1 :egrin:

we must race !!!!!!!!!!!!!!!!!!!!!

I took apart my whole front clip.
Then pulled the engine to clean and paint the engine bay did this in a bout 3.5 hours
I mean I pulled everything in 3hrs not paint also I am not that fast got alot done.

I fixed the MASSIVE oil leak CashMoneys FD had! FINALLY.

Drove it to work, ran a few logs on the way, backed it into a parking space.