Starting Over
#52
Junior Member
Join Date: May 2005
Location: TriCities / Richland
Posts: 40
Likes: 0
Received 0 Likes
on
0 Posts
...scrapping gaskets off with an exacto-knife is a pain in the finger...argh!
oh well, some sacrifices will have to be given up for this all to work right, and its worth it in the end.......long ways to go tho
oh well, some sacrifices will have to be given up for this all to work right, and its worth it in the end.......long ways to go tho
#55
unregistered rex offender
Join Date: Oct 2003
Location: Spokane, Washington
Posts: 1,644
Likes: 0
Received 0 Likes
on
0 Posts
Damn!! You know where all those parts go? After it's done, and you get your car back Don, you guys are gonna have to make a father-son trip up here for the races.
#56
It's a Hammer
Thread Starter
Join Date: Jul 2002
Location: Richland WA
Posts: 998
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by bstrange99
Damn!! You know where all those parts go?
I have a manual
I know how to use the search
I took it apart
I get by with a little help from my friends
I've never done it before.......mwhahahaa
#60
It's a Hammer
Thread Starter
Join Date: Jul 2002
Location: Richland WA
Posts: 998
Likes: 0
Received 0 Likes
on
0 Posts
Re-built RC fuel injectors & flywheel in. It's comming together.
Need to pick up socket for fly wheel nut, gear puller, throw out bearing tool from Harbour Freight today.
Need to pick up socket for fly wheel nut, gear puller, throw out bearing tool from Harbour Freight today.
#62
Junior Member
Join Date: May 2005
Location: TriCities / Richland
Posts: 40
Likes: 0
Received 0 Likes
on
0 Posts
ALMOST THERE!
dr.jones63 and i have gotten the engine just about ready to be dropped into the car. We stripped down the wireing harness and went over it with the red tape and pulled the unneeded emitions plugs (since we threw out the rats nest anyways). cleaned tranny. got new flywheel.
-still need to get done before engine goes into car...
1.get fuel lines
2.get nipple cap offs for the upper intake
hoist engine up
3.swap auto flywheel with the manual
4. attach tranny
dr.jones63 and i have gotten the engine just about ready to be dropped into the car. We stripped down the wireing harness and went over it with the red tape and pulled the unneeded emitions plugs (since we threw out the rats nest anyways). cleaned tranny. got new flywheel.
-still need to get done before engine goes into car...
1.get fuel lines
2.get nipple cap offs for the upper intake
hoist engine up
3.swap auto flywheel with the manual
4. attach tranny
#64
It's a Hammer
Thread Starter
Join Date: Jul 2002
Location: Richland WA
Posts: 998
Likes: 0
Received 0 Likes
on
0 Posts
Snags:
The S5 flywheel has a broken off bolt in one of the flywheel puller holes.
The turbo that came with the JDM was missing bolts on the turbine housing and has excessive play. - Porteded and swapped S5 turbine housing to original S4 turbo.
The S5 flywheel has a broken off bolt in one of the flywheel puller holes.
The turbo that came with the JDM was missing bolts on the turbine housing and has excessive play. - Porteded and swapped S5 turbine housing to original S4 turbo.
Last edited by dr.jones63; 06-20-05 at 03:00 PM.
#66
Hobby or mental illness?
Join Date: Sep 2004
Location: SW Washington
Posts: 478
Likes: 0
Received 0 Likes
on
0 Posts
Looking good! I wish I were putting parts back on my FC! I still have money to spend on my engine.
So Dr. Jones, how did you get the glass beads out of the water pump and housing? The glass will eat the water pump seal, BTW.
So Dr. Jones, how did you get the glass beads out of the water pump and housing? The glass will eat the water pump seal, BTW.
#67
It's a Hammer
Thread Starter
Join Date: Jul 2002
Location: Richland WA
Posts: 998
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by RoadRaceJosh
how did you get the glass beads out of the water pump and housing? The glass will eat the water pump seal, BTW.
#69
It's a Hammer
Thread Starter
Join Date: Jul 2002
Location: Richland WA
Posts: 998
Likes: 0
Received 0 Likes
on
0 Posts
Trany On
Got the pilot berring & pilot berring seal in and lubed, cleaned the flywheel & pressure plate with brake clean, trany bolted up. Tomorrow I hope to set it in the car. I would have had it done last weekend but I worked 4 shifts of overtime.
Thank's to Rick
Thank's to Rick
#72
Junior Member
Join Date: May 2005
Location: TriCities / Richland
Posts: 40
Likes: 0
Received 0 Likes
on
0 Posts
mine...mine...MINE!...hehe....ive put too much sweat and time, and shead too much skin off my dang fingers to let this baby go into the hands of another creature of the family........besides.........mom has her 83, brother has his 88AE, dad has his 89soon to be even more enriched with money.............theres NO WAY im going to let anyone rip this 7 from me........
the young ones have to bust there a$$e$ on their own.....i dont wanna have done all that work just to watch it be handed down to one of the VI's
VI=Village Idiot
the dog in the picture above isnt dead....its ours, but kept getting in our work area cause its so eager to be apart of everything....so we had her go lay down...ns.jones86x got bored and found a toy called a camera and his target lay not too far away...
the young ones have to bust there a$$e$ on their own.....i dont wanna have done all that work just to watch it be handed down to one of the VI's
VI=Village Idiot
the dog in the picture above isnt dead....its ours, but kept getting in our work area cause its so eager to be apart of everything....so we had her go lay down...ns.jones86x got bored and found a toy called a camera and his target lay not too far away...
Last edited by JJ.Jones88x; 06-22-05 at 01:57 AM.
#73
It's a Hammer
Thread Starter
Join Date: Jul 2002
Location: Richland WA
Posts: 998
Likes: 0
Received 0 Likes
on
0 Posts
The VI (Village Idiot) and me have a deal...........for now. Subject to being revoked by me if Im in a bad mood or any slacking by the VI.
http://cgi.ebay.com/ebaymotors/ws/eB...ayphotohosting
http://cgi.ebay.com/ebaymotors/ws/eB...ayphotohosting